Carrier AquaSnap 61AF 022 Скачать руководство пользователя страница 37

Страница: 37 / 44

14.3 - Accessory 00PPG000488200- Heating System Manager type C

Heating system control (as accessory 00PPG000488100-) with

the possibility to obtain additional heating and domestic hot-

water production capacity from a district heating system

Allows control of a non-reversible heating system that includes a

61AF heat pump and two different heat emitter types and/or two

independent comfort zones. For optimised energy efficiency the

heat pump is controlled by a configurable weather compensation

system.
The control box controls the heating and/or domestic hot-water

production support from a district heating system. The control box

supplies power to the circulating pumps. Hot-water production can

be permanent or programmable with a second setpoint at the heat

pump and control of a switching valve.

Heating system example: with the possibility to obtain additional heating and domestic hot-water

productioncapacity from a district heating system

GT1

GT4 P4 SV34

SV31

GT5

SV35

GT7

GT2

GT7:2

SV21

SV27

SV32

GT1:4

GT1:3

GT3

GT..
P..

SV..

61AF + HSM

Heating system

Floor heating

Domestic hot

water in

Hot water

Legend

Thermistors

GT1

Water temperature loop 1

GT1:3

Heat exchanger leaving water temperature, district heating

GT1:4

Heat exchanger entering water temperature, district heating

GT2

Domestic hot water tank temperature

GT3

Outdoor air temperature

GT4

Water temperature loop 2

GT5

Domestic hot water temperature

GT7

Additional domestic hot water tank temperature

GT7:2

Back-up heat exchanger temperature for domestic hot water

Pompes

Pump for water loop 1 (radiators)

External water pump for the heat pump

Pump for water loop 2 (floor heating)

Pump to pre-heat the domestic hot water valve loop

Pump for domestic hot water circulation

Vannes

SV21

Valve for district heating heat exchanger for heating

SV27

Valve for district heating heat exchanger for domestic hot water

SV31

Three-way mixing valve for the back-up heater

SV32

Heating/domestic hot water change-over valve

SV34

Three-way control valve for water loop 2

SV35

Three-way mixing valve for domestic hot water

14 - HEATING SYSTEM MANAGER (HSM)

Содержание AquaSnap 61AF 022













































Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы:

Carrier AquaSnap 61AF 022, Инструкции по установке, эксплуатации и обслуживанию, Страница: 37 / 44

Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы: