background image

- 1

3

-

START-UP

42TW unit is designed to operate in hot and 
humid conditions without condensation 
problem because of the rubber insulated 
drain pan. Refer to the startup checklist in 

page 11 for startup procedure. 

SERVICE 

TO CLEAN COIL

1. Be sure electrical service switch is open, 
locked, and tagged while working on unit. 
2. Remove supply-air grille access panel and 
brush between coil fins with stiff wire brush. 
Follow-up by cleaning with vacuum cleaner. If 
coil is cleaned with air hose and nozzle, take 
care not to drive dirt and dust into other 
components. 

CHECK DRAIN 

Lock open and tag unit electrical service 
switch. 
Check drain pan, drain line and trap at start 
of each cooling season. A standard type pipe 
cleaner for 5/8-in. ID pipe can be used to 
ensure that pipe is clear of obstruction so that 
condensate is carried away. 

CLEAN FAN WHEEL 

Lock open and tag unit electrical service 
switch. 
For access to fan assembly, remove front or 
bottom panel. 

Fan assembly may be removed from its 
tracks if unit has a long conduit lead. Use a 
stiff brush or vacuum to remove dirt and 
debris from scroll.Wipe all fan surfaces with a 
damp cloth. 

CLEAN ELECTRIC HEATER 

Lock open and tag unit electrical service 
switch. 
1. Remove dust, dirt, or foreign material 
before start-up. Do not block normal airflow to 
and from units; blockage may damage 
electric heaters. 
2. Clean heater elements with soft brush or 
vacuum cleaner as necessary. 

CLEAN OR REPLACE AIR FILTERS 

Lock open and tag unit electrical service 
switch. 
At the start of each cooling season and after 
each month of operation (more or less 
depending on operating conditions) replace 
throwaway filter or clean permanent filter. 
THROWAWAY FILTER 

²

 Replace filter with 

a good quality filter. Do not attempt to clean 
and reuse disposable filters. 
PERMANENT FILTER 
1. Tap on solid surface to dislodge heavy 
particles. 
2. Wash in hot water. 
3. Set filter on end so that water drains out 
through slots in frame. Allow filter to dry 
thoroughly. 

See Fig.7 for filter access.

Fig.7

±

Filter Access.

Содержание 42TD Series

















Отзывы: