Carmanah SpeedCheck-18 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 46

Carmanah SpeedCheck-18 Скачать руководство пользователя страница 46

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

46

SPEEDCHECK-15/18 USER MANUAL

10.0 CUSTOMER SERVICE AND WARRANTY

10.0 Customer Service and Warranty

The SpeedCheck products are covered by a limited warranty for the product excluding batteries and a separate
limited warranty for the batteries.

Visit carmanah.com for additional information or contact the Customer Service Department.

Before contacting Carmanah customer service, please have the serial number of your system available, a brief
description of the problem, as well as all details of the installation (location, pole type, type, and quantity of
fixtures). The serial number can be found on the outside of the system on the bottom right corner of the
enclosure.

To contact the Carmanah Customer Service Department:

Mail:

Carmanah Technologies Corporation
250 Bay Street
Victoria, BC Canada V9A 3K5

Phone:

1.250.380.0052
1.877.722.8877 (Toll Free in U.S. and Canada)

Fax:

1.250.380.0062

Email:

[email protected]

Web:

«
...
44
45
46

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов