manualshive.com logo in svg

Carmanah SpeedCheck-18, Руководство пользователя, Страница: 44 / 46

Поделиться
Скачать
Carmanah SpeedCheck-18 Скачать руководство пользователя страница 44

 

  

 

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | 

[email protected]

 | 

carmanah.com

     

44

 

SPEEDCHECK-15/18 USER MANUAL 

9.0 SERVICE & REPAIR 

 

9.5  SpeedCheck Controller Cable Connections (Legacy) 

If your display uses a non-programmable driver board (socketed processor chip and no coin cell battery holder), 
proceed as follows: 

1.  Connect the display cables before connecting the power cable. 

•

 

The 5-pin and 7-pin (1 and 2) connectors go the right LED display. 

•

 

The 3-pin and 7-pin (3 and 4) connectors go to the left LED display. 

 

 

9.6  SpeedCheck Controller Cable Connections (Legacy 

– without Slow Down) 

If your display uses a programmable driver board (with coin cell holder) note the following cable connections: 

1.  Connect the display cables before connecting the power cable. 

•

 

The 5-pin and 7-pin connectors (1 and 2) go the right LED display. 

•

 

The 3-pin and 7-pin connectors (3 and 4) go to the left LED display. 

 

Содержание SpeedCheck-18















































Отзывы:

Нет отзывов