Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

8

SPEEDCHECK-15/18 USER MANUAL

2.0 SYSTEM OVERVIEW

2.2 Typical Configurations – Overview

SpeedCheck display signs are available with a variety of options:

Model

Beacons

Strobes

StreetHub™

Remote Monitoring

SPEEDCHECK-15

(AC Internal)

Optional

Optional

N/A

SPEEDCHECK-15

(AC/Solar Power Cabinet)

Optional

Optional

Optional

SPEEDCHECK-18

(AC/Solar Power Cabinet)

Optional

N/A

Optional

1. SPEEDCHECK-15 with AC power routed to sign

a. AC input wires connect in junction box, located on the sign chassis (see image on following page)
b. Optional 12V circular LED beacons with internal driver connect in junction box (red/black two

conductor cable)

c. Optional strobes prewired to the controller

2. SPEEDCHECK-15 or 18 with Solar/DC battery power in cabinet

a. Two conductor red/black DC power cable coiled up as it exits the junction box conduit fitting
b. Optional 12V circular LED beacons with internal driver connect in junction box. For

SPEEDCHECK-18, optional beacon versions ship with standard load cables pre-attached to a
four-position terminal block on the back panel assembly.

c. Optional strobes prewired to the controller
d. Optional StreetHub™ remote monitoring prewired in the cabinet

3. SPEEDCHECK-15 or 18 with AC/DC power supply in cabinet

a. SPEEDCHECK-15 – two conductor red/black DC power cable coiled up as it exits the junction

box conduit fitting

b. SPEEDCHECK-18 – two conductor red/black DC power cable coiled up as it exits the back panel

conduit fitting

c. Optional 12V circular LED beacons with internal driver connect in junction box. For

SPEEDCHECK-18, optional beacon versions ship with standard load cables pre-attached to a
four-position terminal block on the back panel assembly.

d. Optional strobes prewired to the controller
e. Optional StreetHub™ remote monitoring prewired in the cabinet

Beacons cannot be combined with strobes in the same system.

«
...
6
7
8
9
10
...
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: Philco Страницы: 7

Бренд: SOUNDMASTER Страницы: 5

Juice Go SJUGOBL15E

Бренд: Sandstrom Страницы: 88

Бренд: Vertex Standard Страницы: 4

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 36

Бренд: Makita Страницы: 60

Бренд: Makita Страницы: 10

Бренд: Binatone Страницы: 11

Бренд: Binatone Страницы: 13

Бренд: Hyundai Страницы: 28

Бренд: Hama Страницы: 122

Бренд: Zte Страницы: 26

Бренд: First Alert Страницы: 16

Бренд: Sensors & Software Страницы: 97

Бренд: Roadstar Страницы: 2

Бренд: Roadstar Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды