SET-UP
1. Remove the wireless motion sensor
bottom cover by pressing inward on the
latch.
2. Pull tab to bring out the battery holder
and install four AA alkaline batteries. Be
sure that the battery (+) and (-) terminals
match the (+) and (-) contacts shown in
the battery compartment.
3. The day/night switch should be in the
day/night mode.
4. The timer (or left) switch should be in the
leftmost position (6 s) for test. With the
switch in this position, the light will turn
off approximately 6 seconds after turn-
ing on. This will allow quick testing of the
motion sensor with the light control.
5. Replace bottom cover.
TEST
1. Walk through the coverage area. Note when the light turns on. If the coverage
area needs to be changed, adjust the motion sensor for improved coverage.
Retighten the ball joint screw.
2. After completing the test, determine the amount of on-time you want for the
light to stay on after motion is detected. The timer switch allows the choices of
10 minutes (rightmost switch position) or 3 minutes (center switch position).
3. Also decide if you want the light control to turn on during the day and night
when motion is detected or just at night. Set the Detect switch to the left for
night only operation and to the right for day/night operation.
4. Close the bottom cover.
INSTRUCTION GUIDE
Motion-Activated Driveway Alarm
HS3605
Congratulations on a wise purchase!
ENCLOSED YOU WILL FIND:
• Plug-In Receiver
• Wireless Motion Sensor
• Wireless Remote Control
• Screws
• One 12-volt alkaline battery (installed)
TOOLS NEEDED:
• Phillips screwdriver
BATTERIES NEEDED
(not included):
• Four AA alkaline batteries
PLUG-IN RECEIVER
For use with Under Counter Lighting and any Plug-In Lamp
1.
Test light to be controlled by the Driveway Alarm by turning lamp to “On” posi-
tion. If working properly, turn lamp to “Off” position.
2.
Unplug lamp
at outlet.
3. Plug Receiver into any standard outlet.
4. Plug lamp into Receiver.
5. Turn lamp to “On” position.
6. Use the wireless remote control to test operation.
Note:
Power must be applied continually to the light control. If a wall switch
previously controlled the light control location, this switch must be in the "on"
position.
DETECTION ZONE
Motion is detected in a 60’ x 140˚ range
which will be over 4396 sq. feet. The
mounting bracket can be adjusted to
customize the detection zone.
Note:
As with most motion detection de-
vices, pets or other animals may activate
the unit. Also, walking in a straight line
towards the motion sensor may reduce
operating range. Walking across the
detection field provides the maximum
operational range.
REMOTE CONTROL
Press the "on" or "off" button to override
the system and turn light on or off.
TO REPLACE REMOTE CONTROL
BATTERY
Remove the top screw from the back
of the remote control. Lift off the back
cover, remove old battery and insert new
battery according to the (+,-) placement
guides. Replace the back cover along
with the screw. The remote control will
now be ready to operate.
SOUNDER
Can be turned on/off by switch on side of receiver unit.
MOTION SENSOR INSTALLATION
Note:
The motion sensor can be mounted
or set anywhere, indoors or outdoors, at
a height of 0 to 10 feet from the ground.
For best range and detection, mount at
least 6 feet from the ground.
For mounting:
A. Place adjustable mounting bracket
(provided) where desired (such as a
post, tree, house) and install top screw
into key slot. Then secure the bottom
screw.
B. Slide the motion sensor down onto the bracket. Adjust the motion sensor to
the desired angle.
Note:
To tighten the ball joint, use a Phillips screwdriver to turn the adjustment
screw on the bracket.
Important:
The bottom cover must face downward after installation so that
moisture cannot enter.
Left
COVERAGE AREA
140º
Top View
MOUNTING BRACKET ADJUST-
MENT
60'
Side to Side
Up and Down
Right
Sounder
on/off
switch
