Carlisle ms 8160 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 29

Carlisle ms 8160 Series Скачать руководство пользователя страница 16

MAINTENANCE

MAINTENANCE SCHEDULE

Component

Action

Frequency

MAINTENANCE SCHEDULE

Maintenance schedule below is a general guide. Please

note that the components, action, and frequency

may vary depending on a variety of factors specific to

your application and facility. Maintaining cleanliness,

understanding of equipment, and training personnel will

reduce downtime relating to failed components.

Counter Weight

Check Fastener Tension

6 Months

Toothed Belt

Check Tension

6 Months

Replace

As Needed

Guide Rails

Clean

6 Months/As Needed

Control Box Filters

Check & Clean

Weekly

Gun Mounting Assembly

Check Fastener Tension

6 Months

CONTROL BOX FILTER

INSPECTION

1. Inspect reciprocator control box filters for powder build-

up. If accumulation occurs and is not remedied, it can

lead to overheating of components.

2. Carefully use a flat tool to pry filter cover off.

Return To Contents

PA-19-04-R0 (02/2019)

16 / 29

www.carlisleft.com

MAINTENANCE

EN

«
...
14
15
16
17
18
...
»

Содержание ms 8160 Series






























Отзывы:

Нет отзывов