background image

2

Congratulations on your purchase of the 

Extra

330ARF

. This is a very unique dual-purpose air-

craft, capable of flying any FAI pattern
sequence with ease, while exhibiting remark-
able 3-D capabilities. Every effort has been
made to produce a lightweight, straight, easy to
assemble aircraft. Because of its oversize con-
trol surfaces which are double beveled to allow
for extreme throws, great care must be taken in
the set-up and flying of this airplane. Quality
hardware components have been provided to
allow for 3D set-up while maintaining adequate
mechanical advantage to eliminate flutter. It is
you responsibility as an advanced pilot to fly the
aircraft in an intelligent manner. 

THROTTLE

MANAGEMENT IS A MUST!!!!!!!

Carl

Goldberg Products has flown the 

Extra 330ARF

through a very rigorous flight-testing schedule
and have stressed the airframe beyond all prac-
tical parameters without a single failure. Carl
Goldberg Products will NOT warrant the 

Extra

330ARF

against flutter due to improper set-up

or excessive speed maneuvers. having said
that, we believe you will find the 

Extra 330ARF

to be one of the most responsive, in-the-grove
aircraft on the market. Just remember to use
common sense when flying this high perform-
ance machine.

We are very proud of the construction of the

Extra 330ARF 

and all of our other ARF aircraft.

Each aircraft is jig built to insure a straight true
airframe. Every effort is made to build as light an
aircraft as possible. As with any professional
builder, glue is used sparingly. 

Please take a

moment during assembly and run a bead of
CA or aliphatic resin into the high stress
joints that you can reach such as the landing
gear plate, servo mounting trays, wing hold
down blocks, etc

. Also, during the course of

shipping from the manufacturer to our facility in
the United States, it is not uncommon for the air-
craft to experience several changes in climate.
This may cause the iron-on covering to develop
wrinkles. This is not a fault of the manufacturer.
Please take a few minutes with your heating iron
and heat gun to iron down the seams and re-
shrink the covering where needed. The results
will be a beautiful aircraft  with a breathtaking fin-
ish that you will be proud to display at your flying
club.

Before beginning assembly of your 

Extra

330ARF

, we highly recommend that you study

this manual in its entirety. You should begin
planning your radio installation based on your
choice of engine and equipment from the begin-
ning.

Because the 

Extra 330ARF 

is intended for

those with some degree of modeling experi-
ence, every minute detail will not be covered.
This is not a basic trainer. Assembly of this air-
craft will be easy for the experienced modeler,
and by following the instructions within this
manual and using the skills you’ve gained dur-
ing your modeling career you will be able to pro-
duce a first class aircraft.

Building supplies needed

Hobby knife w/#11 blades
Thin CA
Medium CA
Canopy glue
30 minute epoxy
Thread lock 
Diagonal wire cutters
Pliers
Assorted drill bits
Various sized screwdrivers( both Phillips and
standard head)
Tape measure
Dry-erase marker
Paper towels
Rubbing alcohol
Electrical tape
4-40 Tap & Die Set
3/32, 7/64, 9/64 & 3mm Allen wrench
Wax Paper

Note:

Thread lock must be used where

ever any machine bolts are going into
any type of nuts. If you do not use
thread lock the bolts could become
loose and fall out in flight.

Содержание EXTRA 330 ARF





















Отзывы: