background image

070026-020 

Printed in USA 

August, 2018 

 

A

FTERMARKET 

I

NSTALLATION 

M

ANUAL

 

A

LTITUDE 

A

RMS AND 

C

ANOPY

T

HIS MANUAL PROVIDES INSTRUCTIONS FOR THE 

B

ASIC 

I

NSTALLATION OF THE 

A

WNING

.

RV

 

 

Read this manual before installing or using this product.  Failure to follow the instructions 
and safety precautions in this manual can result in personal injury and/or cause the 
product to not operate properly. 

 

T

ABLE OF 

C

ONTENTS

 

Product Overview .......................................................................................................................... 1

 

Component Checklist.............................................................................................................................. 2

 

Required Pre-Installation Preparation ......................................................................................... 3

 

Upgrades to Existing Awnings ................................................................................................................ 3

 

Installing an Awning Rail ......................................................................................................................... 4

 

Roller Tube Endcaps .............................................................................................................................. 4

 

Top Mounting Brackets ........................................................................................................................... 4

 

Installation ..................................................................................................................................... 5

 

Attaching the Roller Tube ....................................................................................................................... 5

 

Cable Routing at the Top of the Arm .............................................................................................. 5

 

Routing LED Harness to Bottom of the Arm ................................................................................... 5

 

Mounting the Awning .............................................................................................................................. 6

 

Mounting the Arms ......................................................................................................................... 6

 

Securing the Fabric ................................................................................................................................. 7

 

Switch and Wiring Installation ..................................................................................................... 8

 

Wire Routing ........................................................................................................................................... 8

 

Carefree Connects Power Cable ............................................................................................................ 8

 

Awning Control Switch ............................................................................................................................ 9

 

Optional LED’s ............................................................................................................................. 10

 

Switch Installation for LED's ................................................................................................................. 10

 

Optional Wire Covers .................................................................................................................. 11

 

 

Содержание RV














Отзывы: