background image

052876-005r3 

Printed in USA 

February, 2017 

 

I

NSTALLATION 

M

ANUAL

 

F

IESTA 

&

 

F

IESTA 

HD

 

P

ATIO 

A

WNINGS

M

ANUALLY 

O

PERATED 

P

ATIO 

A

WNING

RV

 

 

Read this manual before installing or using this product.  Failure to follow the instructions 
and safety precautions in this manual can result in personal injury and/or cause the 
product to not operate properly. 

 

These instructions apply to Fiesta & Fiesta HD Awnings.  These instructions may also be 

used as reference for the Spirit and Simplicity Awnings that have been discontinued. 

T

ABLE OF 

C

ONTENTS

 

Component Checklist.................................................................................................................... 1

 

Installation ..................................................................................................................................... 2

 

Installing an awning rail (if required) ....................................................................................................... 2

 

Assembling the Awning .......................................................................................................................... 3

 

Mounting the Bottom Mounting Brackets ................................................................................................ 3

 

Mounting the Awning .............................................................................................................................. 4

 

Installing the Stop Bolt .................................................................................................................... 5

 

Securing the Fabric ........................................................................................................................ 5

 

Installing the Rubber Bumpers ....................................................................................................... 5

 

Factory Installed LEDs (Optional) ................................................................................................ 6

 

White LED Schematic and Layout .......................................................................................................... 6

 

Harness Routing into the Vehicle ........................................................................................................... 6

 

Switch Installation ................................................................................................................................... 7

 

 

Содержание FIESTA










Отзывы: