Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 87

Страница: 87 / 378

Programming

2-31

Alaris

System Directions for Use

Pump and Syringe Modules Section

Bolus Dose

(Continued)

CHANNEL

SELECT

CHANNEL

OFF

RESTART

PAUSE

ALARM

INFUSE

STANDBY

ALARM

INFUSE

STANDBY

CHANNEL

SELECT

CHANNEL

OFF

PAUSE

RESTART

RATE (mL/h)

NOTES

If the Bolus Dose feature is enabled, the

BOLUS

soft key

appears in the Continuous Infusion screen and becomes
active when a

VTBI

is entered.

The bolus

VTBI

cannot exceed the programmed continuous

infusion

VTBI

Programming and starting a bolus dose deletes any
programmed delay.

If no continuous rate is entered, the infusion will end when the
bolus has been delivered. No

KVO

infusion will follow.

To see details during the bolus infusion, press the

CHANNEL

SELECT

key.

The Pump Module keypad is used in the illustration but the
key is the same for the Syringe Module.

Restoring Bolus Dose

(Continued)

c. Press

RESTORE

soft key.

d. Verify dosing parameters and press

START

soft key.

Bolus dose completed - module turned off:

a. Press

CHANNEL SELECT

key.

b. Press

RESTORE

soft key.

c. Verify parameters and press

NEXT

soft key.

d. Verify infusion parameters and press

BOLUS

soft key.

e. Press

RESTORE

soft key.

f. Verify dosing parameters and press

START

soft key.

Primary Infusion

- With Guardrails

Suite MX Protection

(Continued)

Содержание Alaris 8000 Series



























































































































































































































































































































































































Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Cardinal Health Alaris 8000 Series, Инструкция по применению, Страница: 87 / 378

Результаты поиска

Содержание Alaris 8000 Series

Отзывы: