Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 378

background image

General Information

3-49

Alaris

®

System Directions for Use

Patient Controlled Analgesia Module Section

Features and Displays

(Continued)

Displays

Configurable Settings

The displays illustrated throughout this document are for
illustration purposes only. The display content will vary,
depending on configuration settings, type of administration set
in use, hospital-defined data set uploaded using the
Guardrails

®

Suite MX, programmed drug calculation

parameters, and many other variables. Refer to specific drug
product labeling for information concerning appropriate
administration techniques and dosages.

Reference the PC Unit Section of this

DFU

for system

configurable settings.

If the configuration settings need to be changed from the
"Factory Default" settings, reference the applicable Technical
Service Manual or contact Cardinal Health Technical Support,
for technical, troubleshooting, and preventive maintenance
information.

With the Profiles feature enabled, the settings are configured
independently for each profile. A hospital-defined, best-
practice data set must be uploaded to enable the Profiles
feature. Date and Time is a system setting and is the same in
all profiles.

«
...
225
226
227
228
229
...
»

Содержание Alaris 8000 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Alaris 8000 Series

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: Facnor Страницы: 33

Бренд: made for movement Страницы: 51

Бренд: Dana Design Страницы: 20

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

i-Digits Access

Бренд: Össur Страницы: 231

Бренд: Ultratune Страницы: 12

Бренд: EzCAP Страницы: 15

Tacx Boost Bundle

Бренд: Garmin Страницы: 12

Бренд: TECshow Страницы: 22

RIDA qLine Scan

Бренд: R-Biopharm Страницы: 24

Бренд: Z-CAM Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды