Cardin Elettronica 205/BLi924 Скачать руководство пользователя страница 13

Страница: 13 / 44

IMPORTANT REMARKS

THE INTEGRATED CARDIN SYSTEMS ARE DESIGNED AND BUILT ONLY

TO BE USED IN MADE TO MEASURE METALLIC STRUCTURES. CARDIN

ELETTRONICA DO NOT GUARANTEE PRODUCTS THAT HAVE BEEN

INSTALLED IN A WAY THAT DOES NOT CONFORM TO THE SUPPLIED

INDICATIONS.

It therefore follows that the structure should be constructed in such a way

as to guarantee the following characteristics:

• Suitable for housing electronic appliances:

- the upper part must be completely sealed, so as not to allow water infiltra-

tion (IP55) (det. A);

- Air vents should be fitted in both the upper and lower parts of the columns

in order to avoid condensate build up (det. B);

• Conformity with the dimensional and structural characteristics as stipulated

by good building practice

• The end structure should respect the parameters as laid down by the stand-

ards and regulations in force UNI EN 12453 with regard to maintaining safety

conditions during the use of motorized gates and doors.

The geared motor is normally installed with the drive shaft pointing up-

wards

(det. A). To position the motor with the driveshaft pointing downwards

(det. C) create a supplementary cover within the column where necessary.

• These instructions are aimed at professionally qualified "

installers of electrical

equipment

" and must respect the local standards and regulations in force.

All materials used must be approved and must suit the environment in which the

installation is situated.

• All maintenance operations must be carried out by professionally qualified techni-

cians. Before carrying out any cleaning or maintenance operations make sure the

power is disconnected at the mains.

• This appliance must be used exclusively for the purpose for which it has been made.

"i.e.

for the automation of hinged gates

" with one or two gate leaves, max.

length

1,8 m

max. weight

150 kg

The unit may be fitted both to the

right

and to the

left

of the passageway and has

a maximum opening angle of

180°

Caution!

a mechanical stop buffer must be installed.

• This appliance must never be used by people (including children) with physical,

sensory or mental disabilities or by people without specific knowledge and experi-

ence in its operation unless they are able to benefit from the experience or are

being taught to use the appliance whilst being safeguarded by the presence of

somebody responsible for their safety.

• Before installing make sure that the guided parts are in good condition, correctly

balanced and that they open and close correctly.

• Avoid becoming trapped between the hinged parts and the fixed parts during the

opening and closing movements.

• The motor’s power cable must be made of polychloroprene in conformity with the

international standard 60245 IEC 57.

It is the responsibility of the installer to make sure that the following public safety

conditions are satisfied:

1) Ensure that the gate operating installation is far enough away from the main road

to eliminate possible traffic disruptions.

2) The motor must be installed on the inside of the property and not on the public side

of the gate. The gates must not open onto a public area.

3) The gate operator is designed for use on gates through which vehicles are passing.

Pedestrians should use a separate entrance. The unit cannot be used together with

a pedestrian door unless it is fitted with a separate device with which to control the

pedestrian door.

4) The controls (including safety controls ) must be installed at a height between

1,5

and

1,8 m

and in a location not accessible to children. Controls installed

externally must be protected by a safety device inhibiting unauthorised use.

5) At least two warning signs (similar to the example on the right)

should be placed, where they can be easily seen by the public,

in the area of the system of automatic operation.

One inside the property and one on the public side of the

installation. These signs must be indelible and not hidden by

any objects (such as tree branches, decorative fencing etc.).

6) Make sure that the end-user is aware that children and/or

pets must not be allowed to play within the area of a gate

installation. If possible include this in the warning signs.

7) Whenever a fully open gate leaf comes within

≤ 500 mm

of a fixed structure

the space must be protected by an anticrush buffer.

8) If you have any questions about the safety of the gate operating system, do

not install the operator. Contact your dealer for assistance.

TECHNICAL DESCRIPTION

• The set consists of:
2 geared motors

200/BLi824

with an incorporated encoder without onboard

electronics;

1 electronic programmer

CC242EUNICB

with

NiMH

batteries, a battery charger

and an integrated

S449

radio frequency module.

• The geared motor is powered by

24 Vdc

and is fitted with a permanently

lubricated four-stage epicycloid reduction unit.

• The geared motor is fitted with an Allen key operated manual release system.
• The geared motor is connected to the electronic programmer by means of a

6 wire cable.

• Electronic programmer for two encoder-controlled

24 Vdc

motors that allow the

precise position control of hinged gates. Monitoring the current consumption
allows the control of a sophisticated anticrush safety system, and the "

soft start

and "

soft stop

" functions reduce the stress on the mechanical components.

The electronic components , housed in a shock-proof plastic container

IP55

, come complete with a battery charger and buffer batteries allow-

ing emergency manoeuvring, a radio frequency module for remote
control and a

Liquid Crystal Display

that allows you to set the system

parameters including: the sequential button mode, automatic reclosing,
warning lamp pre-flashing, intermittent warning lamp activation, indica-
tor light and photoelectric cell function setting and electric lock enable.

Attention!

WEEE marking

. This symbol indicates that once the

products life-span has expired it must be disposed of separately from

other rubbish. The user is therefore obliged to either take the product

to a suitable differential collection site for electronic and electrical

goods or to send it back to the manufacturer if the intention is to

replace it with a new equivalent version of the same product. Suitable

differential collection, environmental friendly treatment and disposal contributes

to avoiding negative effects on the ambient and consequently health as well as

favouring the recycling of materials. Illicitly disposing of this product by the owner

is punishable by law and will be dealt with according to the laws and standards

of the individual member nation.

During the opening/closing manoeuvre check for correct operation and activate the

emergency stop button in case of danger.

During blackouts the gate can be released and manually manoeuvred using the sup-

plied release key (see manual release pag. 14).

Periodically check the moving parts for wear and tear and grease if required using

lubricants which maintain their friction levels unaltered throughout time and are suitable

for temperatures of

-20 to +70°C

In case of failure or operational anomalies switch off the power at the mains do not

attempt to repair the appliance yourself.

Periodically check the correct operation of all safety devices (photoelectric cells etc.).

Eventual repair work must be carried out by specialised personnel using original

spare parts.

The appliance is not suitable for continuous operation and must be adjusted according

to the model (see technical data on page 44).

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL

. NOT READING THESE

IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM AND CREATE
DANGER SITUATIONS FOR THE USERS OF THE SYSTEM. SAVE THESE INSTRUCTIONS FOR FUTURE USE.

USER INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

AUTOMATIC OPENING

KEEP CLEAR

CHILDREN OR PETS MUST NOT

BE ALLOWED TO PLAY ON OR

NEAR THE INSTALLATION

WARNING

205/BLi924

04-08-2010

DI0537

Description :