Carbolite BLF 17/3 Скачать руководство пользователя | Manualshive

Страница: 3 / 17

background image

BLF

S

YMBOLS

& W

ARNINGS

1.1 Switches and Lights

Supply Light: when the furnace is connected to the electrical supply the
light in the adjacent switch glows

Heat Light: the adjacent light glows or flashes to indicate that power is
being supplied to the elements

1.2

Warning Symbols

DANGER of electrical shock– read any warning printed by this symbol.

DANGER – hot surface. Read any warning printed by this symbol.

WARNING: all surfaces of a furnace may be hot.

DANGER – read any warning printed by this symbol.

2.0

MF23

3

«
1
2
3
4
5
...
»

Содержание BLF 17/3


















Отзывы:

Нет отзывов

Похожие инструкции для BLF 17/3

Бренд: Whirlpool Страницы: 8

Бренд: Whirlpool Страницы: 16

Бренд: Whirlpool Страницы: 28

Бренд: Coleman Страницы: 6

Бренд: Continental Refrigerator Страницы: 72

Portable Furnace

Бренд: Arbaco Страницы: 6

Бренд: Lennox Страницы: 54

FC085V42A FH085V42A FH110V48AFH110V60A

Бренд: Bard Страницы: 45

Бренд: Unitary products group Страницы: 12

58CTW 100 Series

Бренд: Carrier Страницы: 60

INDUCED COMBUSTION FURNACES 58RAP

Бренд: Carrier Страницы: 8

Бренд: ICP Страницы: 16

Бренд: PSG Страницы: 40

Бренд: Johnson Controls Страницы: 40

iSEER Smartlite FG7T A Series

Бренд: Nordyne Страницы: 8

Бренд: Nordyne Страницы: 8

Бренд: Nordyne Страницы: 12

Бренд: Nordyne Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды