Network Camera
Installation Guide
Please be sure to read the “Safety Precautions” section for correct use. After reading this Installation
Guide, keep it in a readily accessible location for future reference.
* Some cameras are not available in certain countries or regions.
Caution
Request a professional installer for all installation work. Never try to install the camera yourself.
Doing so may result in unforeseen accidents such as dropping the camera or electric shock.
Check Included Items
Camera
Template
Installation Guide (This document)
Setup CD-ROM
Warranty Card
Ceiling Plate
Safety Wire, Screws (M4) x 2
Dedicated wrench
RJ45 Coupler
LAN Cable Cap
Packing Attachment
Waterproof Packing
Zip Tie
GND Screw (M3) x 1
Multi-Cable
Waterproofing Tape
Waterproofing explanation sheet
BIE-7174-000
Safety Precautions
This Installation Guide uses the following symbols to indicate important information the user should know in order
to use the product safely. Explanations are provided for each symbol so that users will understand the level of
importance for each. Be sure to observe these items.
Installation Precautions
Warning
Failure to follow the instructions may result in death or serious injury.
Do not install in the following places:
• Places in strong direct sunlight, near heat-generating objects, or locations subject to high
temperatures
• Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.)
• Places subject to oily smoke or steam
• Confined or enclosed places
Failure to do so may result in fire or electric shock.
• Insulate the ends of cables you are not using.
Failure to insulate may result in fire or electric shock.
Notes on Power Supply
• Only use the dedicated AC adapter (sold separately) for AC power.
• Do not set any heavy objects on the power cable (or the LAN cable for a PoE+/PoE power supply).
• Do not pull, forcibly bend, scratch, or modify the power cable (or the LAN cable for a PoE+/PoE power
supply).
• Do not cover or wrap the AC adapter (sold separately) with cloth or blankets.
Failure to do so may result in fire or electric shock.
Caution
Failure to follow the instructions may result in injury.
For installation or inspection of this camera, consult the dealer where you purchased the product.
• This installation should be made by a qualified service person and should conform to all local codes.
• When installing, make sure the surface is capable of withstanding the total weight of the camera and
accessories, and sufficiently reinforce if necessary.
• Be sure to use installation screws designed for the type of surface the camera is to be installed.
• Periodically check the parts and screws for rust and loosening, in order to prevent injuries and
equipment damage due to falling items.
• Do not install in unstable places, places subject to significant vibration or impact, or places subject to
salt damage or corrosive gas.
• Do not install in places subject to strong winds.
• Do not install where snow can accumulate directly on the camera.
• Be sure to attach the safety wire when installing the camera.
Failure to do so may result in the camera falling or other accidents.
• Do not touch the edges of metal parts with bare hands.
• Be careful not to get your fingers caught when installing.
Failure to do so may result in injuries.
• Avoid looking directly at the infrared illumination at close distances for long periods of time.
Intense infrared illumination can cause eye damage.
Caution
Failure to follow the instructions may result in property damage.
• Do not install on an unstable surface.
• To maximize shock resistant specifications, do not install on insufficiently strong surfaces or surfaces
subject to significant vibration.
• After turning off the power, do not turn the power on again for at least five seconds.
• Take measures to remove static electricity before performing any procedures.
• If there is condensation, please wait to power on, until the condensation dissipates.
• Please waterproof and dust-proof camera, when installing outdoors.
Failure to do so may result in malfunctions.
• Take care not to damage wiring or piping.
Failure to do so may result in damage to peripheral items.
Important
We recommend the installation of a lightning arrester (a surge protection device) as a measure against failures caused by
lightning strikes. Please refer to our website for details.
Precautions for Installing the Camera Outdoor
When installing the camera outdoors, observe the following precautions to retain
waterproof/dustproof capabilities.
• Use the sunshade cover (sold separately) when installing in a location with direct
sunlight.
• Completely wrap the cable connections and the ends of cables you are not using,
including the connectors, with waterproof tape up to the cable jacket, so as not to
allow water to enter. Please refer to the waterproofing explanation sheet for details on
how to wrap the waterproofing tape.
• When mounting the camera onto a wall or other upright surface, make sure that the
cables and composite pipe are facing down to prevent rain infiltration.
• If wiring the camera through the wiring hole on the bottom, use silicone sealant or a
rubber mat to ensure waterproofing. Also use an insect repellent sponge if necessary.
• Firmly fix the dome case to the main unit of the camera with the lock screws, taking
care not to pinch cables between the main unit and dome case.
Precautions for Use
Warning
Failure to follow the instructions may result in death or serious injury.
• If you discover defective conditions such as smoke, strange sounds, heat or strange odors,
immediately stop using the camera and contact your nearest dealer.
Fire or electric shock may result from continued use of the product.
• If thunder starts, stop installation or inspection etc. and do not touch the camera or continue
connecting the cable.
• Do not disassemble or modify the camera.
• Do not damage the connecting cable.
• Do not insert foreign objects such as water or metal into the camera.
• Do not use flammable sprays near the camera.
• Do not leave LAN cables, external power supply, or the power connector for the AC adapter (
sold
separately
) connected when the camera is not in use for long periods.
• Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning the camera.
Failure to do so may result in fire or electric shock.
Specifications
Please refer to the installation procedures or the Appendix – Specifications for specifications not listed below.
Lens
2.4x optical zoom (4x digital zoom) lens (electric drive)
Viewing Angle
For 16:9 aspect ratios
Horizontal: 122.1° (W) – 50.1° (T)
Vertical: 65.9° (W) – 28.1° (T)
For 4:3 aspect ratios
Horizontal: 89.2° (W) – 37.5° (T)
Vertical: 65.9° (W) – 28.1° (T)
Pan Angle Range
360° (±180°)
Tilt Angle Range
90° (-15° – +75°)
– Camera is at 0° when attached to the ceiling and facing straight down
Rotation Angle Range 350° (+220°/-130°) +: Clockwise
Network Terminal
LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))
– Use a category 5 or better LAN cable, 100 m (328 ft.) or less in length.
Audio Input Terminal
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(Common for LINE IN & MIC IN)
Audio Output Terminal 3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(LINE OUT)
External Device I/O Terminal Input x 2, Output x 2
Analog Video Output x 1
Memory Card
microSD Memory Card, microSDHC Memory Card, microSDXC Memory Card Compatible.
Operating Environment Temperature:
When the heater unit (sold separately) is installed
Operating Temperature Range:
AC, PoE+: -40°C – +55°C (-40°F – +131°F)
Start-up Temperature Range:
AC, PoE+: -30°C – +55°C (-22°F – +131°F)
– Sunshade cover (sold separately) necessary when under direct sun exposure
When the heater unit (sold separately) is not installed
AC, DC, PoE+, PoE: -10°C – +55°C (+14°F – +131°F)
– Sunshade cover (sold separately) necessary when under direct sun exposure
Humidity: 5% – 85% (without condensation)
Storage Environment
Temperature: -30°C – +60°C (-22°F – +140°F)
Humidity: 5% – 90% (without condensation)
Installation Method
Ceiling mount/Surface mount
Power Supply
PoE: PoE power supply via LAN connector (IEEE802.3at Type1/Type2 compliant)
AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)
External power source: 24 V AC/12 V DC
IR Illumination Range 20 m (65.6 ft.)
Power Consumption
PoE+: Max. approx. 12.4 W*
1
Max. approx. 23.1 W*
1
*
2
PoE: Max. approx. 12.4 W*
3
AC Adapter PA-V18: Max. approx. 15.2 W (100 V AC)
Max. approx. 15.2 W (240 V AC)
DC: Max. approx. 13.8 W
AC: Max. approx. 12.7 W
Max. approx. 24.1 W*
2
*
1
Class 4 power sourcing equipment (requests 30.0 W)
*
2
When the heater unit (sold separately) is installed
*
3
Class 0 power sourcing equipment (requests 15.4 W)
Weight
Approx. 1850 g (4.08 lb.)
Impact Resistance
IK10 (20J)
Dust-resistant/
Waterproof Specification IP66
Part Names
9
6
8
4
5
3
2
1
12 13
7
14 15 16
18
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
10
11
17
1. Dome case lock screw / 2. Dome case / 3. Reboot switch / 4. Installation adjustment switch /
5. Power connection terminal / 6. GND screw hole / 7. Analog video output terminal / 8. Audio I/O terminal /
9. Lens unit / 10. 100Base-TX LAN connector / 11. Heater connection terminal / 12. LED (Blue)* /
13. External device I/O terminals / 14. Fan / 15. Visible light sensor / 16. Memory card slot /
17. Infrared illumination / 18. Connection slot
* On: when powered on, during reboot / Off: during normal use
External Dimensions
Camera mounting tab slots
145 (5.71)
180
(7.09)
R62 (R2.44)
Unit: mm (in.)
Unit: mm (in.)
10- 4.5 ( 0.18)
(*1*2)
6.6 (0.26)
18.5 (0.73)
83.5 (3-9/32)
(*4)
85.7 (3-3/8)
(*3*4)
85.7 (3-3/8)
(*
3*
4)
46
(
1-
13
/1
6)
(*
3*
4)
85.7 (3-3/8)
(*
4)
4.5 (0.18)
4.5 (0.18)
4.5 (0.18)
171 (6.73)
*1 Ceiling/Wall mount holes
*2 Junction box fixing holes
*3 Ceiling/Wall mount holes position
*4 Junction box fixing holes position
Before Installing the Camera
Set the IP address and other network information on the camera using the “Camera Management Tool” on the
Setup CD-ROM. For details on how to operate the “Camera Management Tool”, please refer to the “Camera
Management Tool User Manual”.
Preparing the analog monitor
The analog video output video image is used by this camera to adjust the camera’s viewing angle.
Attaching the packing attachment and removing the dome case
Remove the outer tape. Attach the included packing attachment to the connection slot that the cable will pass
through, and attach the connection slot cover to the connection slot that the cable will not pass through. Use a
coin to remove the connection slot cover.
Remove the dome case and remove the tape and polystyrene foam attached to the lens for shipping purposes.
When guiding cables through
the side
When guiding cables through
the bottom
❶
❷
Dedicated wrench
Packing Attachment
Guiding the LAN cable through the waterproof packing
Using a Memory Card
Remove the dome case and place the memory card in the memory card slot.
To remove the memory card, push it in all the way until the card slightly pops
out and remove.
Important
• Insert a memory card before installing the camera.
• When using a memory card with the camera for the first time, it is recommended
to format the card after inserting it into the camera (please refer to “Operation
Guide”).
• Always unmount the memory card before removing it (please refer to “Operation
Guide”).
Memory card slot
Using the Heater Unit (sold separately)
Connect the two heater cables included with the heater unit to the terminals on the camera side. Next, attach the
heater unit to the camera body and then tighten the screws. Finally, connect the cables to the heater unit.
❶
❷
❸
Using the Dome Unit (sold separately)
Remove the dome case from the camera, then remove the dome cover holder and dome flange, and replace with
the smoked dome.
Important
• Take care when replacing so as not to scratch the dome cover.
• For proper protection against water and dust, please make sure the screws are firmly tightened during installation.
Dome flange
Dome cover
Rubber seal
Dome cover holder
Smoked dome cover
Using the Sunshade Cover (sold separately)
The sunshade cover is attached to the camera body together with the dome case. In order to install it, of the four
lock screws for the dome case, remove the two located at the top of the dome case beforehand. Remove the
dome case lock screws by pressing the screws from the inside of the case and using the dedicated wrench to
loosen them.
Dedicated
wrench
ENGLISH
Accessories
The following accessories can be purchased separately as necessary. Some accessories are not available in
certain countries or regions.
Pendant Mounting Kit PC640-VB
Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box
stores.
Dome Unit DU652-S-VB
Smoked dome cover.
Sunshade Cover SC640-VB
Dedicated accessory to protect the camera body from direct sunlight.
Heater Unit HU652-VB
Dedicated accessory attached to the interior to maintain operation temperature within the dome and achieve stable
operation even in extremely cold environments.
Canon AC Adapter PA-V18
Dedicated AC adapter for this camera.
The contents of this guide are subject to change without any prior notice.
© CANON INC. 2016
Printed in Japan
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
These symbols indicate that this product is not to be disposed of with your household waste, according to
the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC) and/or national
legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in accordance with the
Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb =
Lead) is present in this battery or accumulator at a concentration above an applicable
threshold specified in the Battery Directive.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one
basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and
electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could
have a possible impact on the environment and human health due to potentially hazardous substances that
are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office, waste authority,
approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.
canon-europe.com/battery.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
