Canon VarioPrint 6000 Series Скачать руководство пользователя страница 266 | Manualshive

Страница: 266 / 354

background image

Perform a media registration for standard-size media -

Print the test sheets and create the ruler

Introduction

The different properties of media can influence the alignment of images when the media are
printed. To ensure a correct alignment, you can perform a media registration for each individual
media in the [Media catalog]. The following values will be measured.
• The Z-position of side 1
• The X-length of side 1
• The Z-position of side 2
• The X-position of side 1
• The X-position of side 2.

For each media registration, a paper ruler and 3 test sheets will be printed. Depending on the
regional setting in the Settings Editor, the paper ruler is printed on A4 or Letter. You can use the
first printed sheet to create the paper ruler. However, you can also use a universal ruler of your
own. The ruler must be long enough to carry out the measurements. You must carry out each
measurement on all 3 test sheets. The system calculates the average value of the measurements.

This section describes how to perform a media registration for standard-size media (media with a
length of less than 390 mm / 15.35").

NOTE

It is recommended to perform the media registration when the list of [Scheduled jobs] is empty.

Before you begin

1. On the control panel, press the [System] button.
2. Press [Media].
3. Select a media from the [Media catalog] for which you want to perform a media registration.
4. Press [Optimize].

When a maintenance PIN is defined in the Settings Editor, a numerical keyboard appears.

5. Enter the maintenance PIN to start the wizard.

NOTE

The following procedures often refer to the start of the ruler. The start of the ruler is the line

where the shaft of the arrow starts.

Procedure

1.

Read the introduction on the screen. Then press [Next].
The printed test sheets go to the system output.

2.

Take the first printed sheet.

Perform a media registration for standard-size media - Print the test sheets and create the ruler

266

Chapter 11 - Media handling

VarioPrint 6000 line

«
...
264
265
266
267
268
...
»

Содержание VarioPrint 6000 Series



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VarioPrint 6000 Series

Бренд: Brother Страницы: 53

Бренд: Brother Страницы: 64

Word Processor WP-700D

Бренд: Brother Страницы: 172

SX 4000 - ELEC LCD DISP Typwriter

Бренд: Brother Страницы: 54

Бренд: Brother Страницы: 2

Бренд: Brother Страницы: 56

Бренд: Brother Страницы: 65

Бренд: Brother Страницы: 96

Бренд: Brother Страницы: 44

Бренд: Brother Страницы: 100

Бренд: Brother Страницы: 56

Бренд: Brother Страницы: 56

Бренд: Brother Страницы: 36

Бренд: Brother Страницы: 62

Ensemble PDP-100J

Бренд: Brother Страницы: 3

ML-500 - Electronic Word Processing Typewriter

Бренд: Brother Страницы: 118

Бренд: Brother Страницы: 116

WhisperWriter WP-7400J

Бренд: Brother Страницы: 252

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды