Canon MP630 SERIES Скачать руководство пользователя страница 8

Страница: 8 / 47

*1: Only for models supporting CD / DVD printing
*2: Only for models not supporting CD / DVD printing

the OK button.

Multiple ink tanks of the

same color installed.

[1681] U071 More than one ink tank of the following

color is installed.

Replace the wrong ink tank(s) with the correct one(s).

Ink tank in a wrong

position.

[1680] U072 Some ink tanks are not installed in

place.

Install the ink tank(s) in the correct position.

Warning: The ink

absorber becomes almost

full.

[1700,

1701]

---

Contact the support center or service

center for ink absorber replacement.

Press [OK] to continue printing.

Replace the ink absorber, and reset its counter. [See

3-3.

Adjustment / Settings, (6) Service mode.

]

Pressing the OK button will exit the error, and enable

printing without replacing the ink absorber. However,

when the ink absorber becomes full, no further printing

can be performed unless the applicable ink absorber is

replaced.

The connected digital

camera or digital video

camera does not support

Camera Direct Printing.

[2001]

---

The device may be incompatible.

Remove the device and check the

manual supplied with the connected

device.

Remove the cable between the camera and the machine.

Automatic duplex printing

cannot be performed.

[1310]

---

This paper is not compatible with

duplex printing. Remove the paper and

press [OK].

The paper length is not supported for duplex printing.

Press the OK button to eject the paper being used at error

occurrence.

Data which was to be printed on the back side of paper at

error occurrence is skipped (not printed).

Failed in automatic print

head alignment.

[2500]

---

Auto head align has failed. Press [OK]

and repeat

operation. <See manual>

Press the OK button to clear the error, then perform the

automatic print head again.

(In the MP630 / MP638, use Matte Photo Paper MP-101.)

The remaining ink amount

unknown.

[1683] U130 (Applicable ink tank icon)

The remaining level of the following

ink cannot be correctly detected.

Replace the ink tank.

An ink tank which has once been empty is installed.

Replace the applicable ink tank with a new one. Printing

with a once-empty ink tank can damage the machine.

To continue printing without replacing the ink tank(s),

press the Stop button for 5 sec. or longer to disable the

function to detect the remaining ink amount. After the

operation, it is recorded in the machine EEPROM that the

function to detect the remaining ink amount was disabled.

Ink tank not recognized.

[1684] U140 The following ink tank cannot be

recognized.

(Applicable ink tank icon)

A non-supported ink tank (an ink tank that is sold in a

different region from where the machine was purchased)

is installed (the ink tank LED is turned off). Install the

supported ink tanks.

Ink tank not recognized. [1410 to

1419]

U150 The following ink tank cannot be

recognized.

(Applicable ink tank icon)

A hardware error occurred in an ink tank (the ink tank

LED is turned off). Replace the ink tank(s).

No ink (no raw ink).

[1688] U163 Printer detected ink out condition of the

following ink. Replace the ink tank.

(Applicable ink tank icon)

Replace the empty ink tank(s), and close the scanning

unit (cover).

Printing with an empty ink tank can damage the machine.

To continue printing without replacing the ink tank(s),

press the Stop button for 5 sec. or longer to disable the

function to detect the remaining ink amount. After the

operation, it is recorded in the machine that the function

to detect the remaining ink amount was disabled.

Non-supported hub

[2002]

--- An unsupported USB hub is connected.

Remove the hub.

Remove the applicable USB hub from the PictBridge

(USB) connector.

Time-out in CD / DVD

print operation.

[1830

] --- Timeout error has occurred. Press [OK]. A prescribed period of time (12 minutes) has elapsed

without any printing since printing was attempted. Press

the OK button to clear the error.

Time-out for the scanner

device

[2700]

--- Timeout error has occurred. Press [OK]. The buffer became full in the middle of scanning

operation, and 60 minutes have elapsed since then,

making re-scanning unstable. Press the OK button to clear

the error.

6 / 45

Содержание MP630 SERIES
















































Результаты поиска

Содержание MP630 SERIES

Отзывы:

Похожие инструкции для MP630 SERIES

Бренды по названию

Популярные бренды

Canon MP630 SERIES, Руководство по обслуживанию

Результаты поиска

Содержание MP630 SERIES

Отзывы:

Похожие инструкции для MP630 SERIES

Бренды по названию

Популярные бренды