Canon iR2318 series Скачать руководство пользователя страница 38

Страница: 38 / 308

Chapter 1

1-18

1.2.3.9 System Settings

0021-9501

* Factory setting (It may be different depending on the countries or region of destination.)

Additional Functions

Settings

System Manager Set.

System Manager ID, System Manager

Device Info Settings

Device Name, Location

Dept. ID Management

Off(*), On:

Reg./Edit Dept. ID:

Department ID, Password, Limit Settings, Erase

Page Totals:

View Page Totals, Clear All Totals, Print List

Allow Unkn. ID Print: Off, On(*)

Allow Unkn. ID Scan: Off, On(*)

User ID Management

Off(*), On

Network Settings

TCP/IP Settings, SNMP Settings, Ethernet Driver, Startup Time Set.

Remote UI On/Off

Off, On(*)

Job Log Display

Off, On(*)

Use USB Device

Off, On(*)

Update Firmware

This function is only used when the firmware needs to be updated.

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 38 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: