Canon iR2318 series Скачать руководство пользователя страница 227

Страница: 227 / 308

Chapter 9

9-17

9.4.10 Fixing Driver Motor

9.4.10.1 Removing the Fixing Unit Drive Motor

0020-4487

1) Draw out the drum unit.

2) Remove the rear cover.

3) Remove the left cover (rear).

4) Remove the left door.

5) Remove the fixing unit.

6) Remove the image processor PCB with the PCB mount.

7) Remove the fixing motor [1].

- Connector [2] 1 pc.

- Screws [3] 2 pcs.

F-9-50

9.4.11 Left Door

9.4.11.1 Removing the Left Door (Non Duplex Unit Type)

0020-4488

1) Draw out the drum unit.

2) Remove the rear cover.

3) Remove the left cover (rear).

4) Release the duplex unit harness [1].

- Screw [2] 1 pc.

- Connector [3] 1 pc.

- Reusable band [4] 1 pc.

- Wire saddle [5] 1 pc.

F-9-51

5) Open the left door until it sops and pull out the hinge shaft [1].

F-9-52

6) Lift the left door with both hands to release it from the door rotation shaft

[1], and then remove the left door.

F-9-53

[3]

[2]

[1]

[2]

[3]

[4]

[5]

[1]

MEMO:

When a duplex unit (option) is installed, remove it before pulling out the
hinge shaft for each access.

[1]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 227 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: