Canon iR2318 series Скачать руководство пользователя страница 191

Страница: 191 / 308

Chapter 7

7-23

3) Lower the separation roller [1] as shown below, and then remove the sep-

aration roller [1] and feed roller [3] by holding the claws [2] of the roller

collars.

F-7-56

7.5.14 Separation Pad

7.5.14.1 Removing the Separation Pad

0020-4443

1) Open the front cover.

2) Turn the developer pressure release lever clockwise, and then open the left

door.

3) Draw out the drum unit.

4) Remove the transfer registration unit [1].

- Screw [2] 4 pcs.

F-7-57

5) Remove the feed guide [1].

- Screw [2] 2 pcs.

F-7-58

6) Remove the multi-paper roller.

7) I use a minus screwdriver and remove separation pad [1].

F-7-59

[3]

[1]

[2]

[1]

[2]

[1]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 191 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: