manualshive.com logo in svg

Canon iR2318 series, Руководство по обслуживанию, Страница: 179 / 308

Поделиться
Скачать
Canon iR2318 series Скачать руководство пользователя страница 179

Chapter 7

7-11

7.2.1.3 Duplex Paper Sensor 1 Delay Jam

0020-5034

Duplex paper sensor 1 delay jam

This jam occurs if the duplex paper sensor 1 does not turn on within the predetermined time after the delivery sensor in the host machine turns on.

7.2.1.4 Duplex Paper Sensor 2 Delay Jam

0020-5035

Duplex paper sensor 2 delay jam

This jam occurs if the duplex paper sensor 2 does not turn on within the predetermined time after the duplex reversal motor starts rotating.

7.2.2 Stationary Jams

7.2.2.1 Stationary Jam in Pickup Assembly

0020-4131

Stationary Jam in Pickup Assembly

The registration sensor does not detect absence of paper within the prescribed time before the next leading edge of fed paper reaches the registration sensor.

7.2.2.2 Stationary Jam in Delivery Assembly (Paper Trailing Edge Stationary Jam at First Delivery Sensor/Stationary Jam 

at First  Delivery Sensor)

0020-5101

Paper Trailing Edge Stationary Jam at First Delivery Sensor

The first delivery sensor cannot detect absence of paper within the prescribed time after the registration sensor has been turned off.

Stationary Jam at First Delivery Sensor

The first delivery sensor cannot detect absence of paper within the prescribed time after it has detected the leading edge of paper.

7.2.2.3 Duplex Paper Sensor 1 Stationary Jam

0020-5036

Duplex paper sensor 1 stationary jam

This jam occurs when the duplex print paper sensor 1 does not turn off when the paper with a longitudinal length of less than 280 mm reaches the standby point

(about 90 mm downstream from the duplex paper sensor 2).

7.2.2.4 Duplex Paper Sensor 2 Stationary Jam

0020-5037

Duplex paper sensor 2 stationary jam

This jam occurs when the duplex paper sensor 2 does not turn off when the predetermined time lapses after the feed motor starts rotating.

7.2.3 Other Jams

7.2.3.1 Door Open Jam

0020-4133

Sensors

Delivery sensor (SR202)

Duplex paper sensor 1(SR1002)

Sensor

Duplex paper sensor 2 (SR1003)

Sensor

Registration sensor(SR209)

Sensor

Registration sensor (SR209)

First delivery sensor (SR203)

Sensor

First delivery sensor (SR203)

Sensor

Duplex paper sensor 1 (SR1002)

Sensors

Duplex paper sensor 1 (SR1002)

Duplex paper sensor 2 (SR1003)

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов