Canon iR2318 series Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 308

Canon iR2318 series Скачать руководство пользователя страница 164

Chapter 6

6-12

7) Select "BitSwitch14" using the arrow key, and hen press the OK key.

8) Select "SW-14-1" using the arrow key, and hen press the OK key.

9) Select "On" using the arrow key, and hen press the OK key.

10) Press the Reset key to exit the service mode.

11) Close the front cover. The machine will run in the developer idling mode

for about 1 minute.

12) When the machine stops, the idling mode ends.

Install, the toner cartridge following the above-mentioned procedure.

6.10.3 Transfer Charging Roller

6.10.3.1 Removing the Transfer Charging Roller

0020-4416

1) Open the left door.

2) Remove the transfer charging roller [1]

F-6-21

Do not touch the transfer charging roller surface.

MEMO:

The transfer charging roller bearing [1] could be the same shape as the
figure below. If so, detach the transfer charging roller towards the arrow [3]
and [4]. Gear [5] will come off when detaching the transfer charging roller.
Be careful not to lose the gear [5]. When attaching the transfer charging
roller, apply transfer charging roller D cut[6] to gear [5] D cut.

[1]

[5]

[1]

[6]

[2]

[2]

[5]

[3]

[4]

«
...
162
163
164
165
166
...
»

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов