manualshive.com logo in svg

Canon iR2018 Series, Портативное руководство, Страница: 19 / 122

Поделиться
Скачать
Canon iR2018 Series Скачать руководство пользователя страница 19

Chapter 3

7

Chapter 3  Error Code

3.1 Error Code Details

3.1.1 Error Code Details

0017-6037

iR2022i / iR2025 / iR2030 / iR2018  / iR2022 / iR2018i

T-3-1

Display 

Code

Detail Code

Main Cause/Symptom

Countermeasure

E000

0000

Startup error

The temperature detected by the main or sub thermistor does 
not rise to the specified value during startup control.

- Check the fixing film connector.
- Replace the fixing film unit.
- Replace the DC controller PCB. 

E001

0000

Abnormally high temperature (detected by main thermistor)

The main thermistor detected an abnormally high temperature 
(240 deg C) during temperature control. 

- Check the connector of the fixing film unit.
- Replace the fixing film unit. 
- Replace the DC controller PCB.

0001

Abnormally high temperature (detected by sub thermistor) 

The sub thermistor detected an abnormally high temperature 
(295 deg C) during temperature control.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E002

0000

Low temperature during temperature control. 

The target temperature is not reached during temperature 
control.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E003

0000

Abnormally low temperature (detected by main thermistor)

After the temperature detected by the main thermistor has 
reached the specified value, it does not reach the specified value 
during initial rotation.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

0001

Abnormally low temperature (detected by sub thermistor) 

After the temperature detected by the sub thermistor has 
reached the specified value, it does not reach the specified value 
during initial rotation.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.

E007

0000

Fixing film sensor failure

The fixing film sensor is faulty. 

- Check the connector of the fixing film sensor. 
- Replace the fixing film sensor.
- Replace the DC controller PCB.

E010

0000

Main motor failure

The main motor is faulty. 

- Check the connector of the main motor. 
- Replace the main motor.
- Replace the DC controller PCB.

E019

0000

Waste toner full detection 

The waste toner full state was detected.

Replace the drum unit.

0001

Waster toner full detection sensor is faulty. 

The waste toner full state was detected continuously for five or 
more seconds while the main motor was turning.

- Check the connector of the waster toner full sensor. 
- Replace the waste toner full sensor.
- Replace the DC controller PCB.

E052

0000

Erroneous connection to duplex unit 

Disconnection of the duplex unit was detected after power-on, 
detection of normal connection to the duplex unit, and start of 
communication. 

- Check the connectors of the duplex unit and DC controller PCB. 
- Replace the duplex controller PCB. 
- Replace the DC controller PCB.

E100

0000

BD detection PCB failure 

The BD detection PCB is faulty.  

- Check the connector of the BD detection PCB. 
- Replace the laser scanner unit. 
- Replace the DC controller PCB.

Содержание iR2018 Series



























































































































Отзывы:

Нет отзывов