Canon iPF9000 series, Руководство по обслуживанию

Страница: 293 / 432

Chapter 6
6-3
<Countermeasure>
1) Clean the printhead
2) Replace the printhead
3) Replace the head management sensor unit.
4) Select [SERVICE MODE] > [ADJUST] > [NOZZLE CHK POS].
5) Head relay PCB
Check the terminal connected to the printhead. If there is any problem, replace the head relay PCB.
6) Replace the carriage relay PCB
7) Replace the main controller PCB
6.1.2.10 Prepare for parts replacement. Call for service.
0014-9214
iPF9000
<Cause>
Replacing time of the consumable parts are near.
<Probable fault location>
Consumable parts, main controller PCB
<Countermeasure>
1) Consumable parts
Check [SERVICE MODE] > [COUNTER] > [PARTS CNT.]
If there is a COUNTER showing "W1" status (over 90% of the use rate), replace the consumable parts corresponded to the COUNTER.
After replacing the parts, select [SERVICE MODE] > [INITIALIZE] > [PARTS COUNTER] to initialize the counter.
2) Replace the main controller PCB
6.1.2.11 Parts replacement time has passed. Call for service.
0014-9215
iPF9000
<Cause>
The consumable parts need to be replaced.
<Probable fault location>
Consumable parts, main controller PCB
<Countermeasure>
1) Consumable parts
Check [SERVICE MODE] > [COUNTER] > [PARTS CNT.]
If there is a COUNTER showing "W2" status (over 100% of the use rate), replace the consumable parts corresponded to the COUNTER.
After replacing the parts, select [SERVICE MODE] > [INITIALIZE] > [PARTS COUNTER] to initialize the counter.
2) Replace the main controller PCB
6.1.3 Troubleshooting When Errors Occur
6.1.3.1 03870001-2015 Cutter error
0012-6626
iPF9000
<Cause>
The machine has failed the auto cutting of media.
After roll media cutting, the multi sensor could not detect the media end.
<Probable fault location>
Media, multi sensor, cutter unit, head relay PCB, or main controller PCB
<Countermeasure>
1) Manual cut
Cut the media manually with the scissors or cutter.
2) Media check
If the media size is not the specified one, replace the media.
3) Visual check
Remove foreign substances from the cutter unit if any.
If the cutter unit is damaged or deformed, replace it.
4) Replace the multi sensor
5) Replace the main controller PCB
6.1.3.2 03010000-200C/03010000-200E/03010000-200F/03010000-2017/03010000-2018/03016000-2010 multi sensor
0013-6968
iPF9000
<Cause>
When media was fed, the multi sensor could not detect the media width.
When the right edge of media was detected, the multi sensor detected that the media had been loaded at a wrong position.
When the leading edge of media was to be detected, the multi sensor could not detect the leading edge of media.
When media was fed, the multi sensor detected media smaller than the specified size.
When media was fed, the multi sensor detected media larger than the specified size.
When media wad fed, the multi sensor detected skew greater than the specified one.
When media was fed, the multi sensor could not detect the right edge of media.
When media was fed, the multi sensor could not detect the left edge of media.
<Probable fault location>
Media, media loading method, paper path, multi sensor, head relay PCB, carriage relay PCB, or main controller PCB
<Countermeasure>
1) Media check
If there is any print or stain in the detection area on the media or the media size is not the specified one, replace the media.
2) Media loading position check
If the media loading position is wrong, load the media again.
3) Visual check