Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя | Manualshive

Страница: 29 / 204

background image

Chapter 1

1-15

1.6 Basic Operation

1.6.1 Operation Panel

0012-6207

The functions of the keys and meanings of LED indications on the operation panel are described below.

F-1-15

[1] Display

Displays the printer menu, status or messages.

[2] Data lamp (green)

"Blinking" The printer is receiving or processing a print job when it is printing.
The printer has suspended a print job or is receiving firmware data when it is not printing.
"Off" No print job is available.

[3] Message lamp (orange)

"Lit continuously" A warning message is on display.
"Blinking" An error message is on display.
"Off" The printer is normal or is powered off.

[4] Online key

Switches the printer between two alternative modes: online and offline.
"Lit continuously" The printer is in online mode. Lights green.
"Off" The printer is in offline mode.

[5] Menu key

Displays a printer main menu.

[6] Paper source selector

[a] Roll media lamp (green)
"Lit continuously" Roll media have been selected as a paper source.
"Off" Cut media have been selected as a paper source.
[b] Cut media lamp (green)
"Lit continuously" Cut media have been selected as a paper source.
"Off" Roll media have been selected as a paper source.

[7] Paper source selector key

Toggles a paper source between roll and cut media each time the key is pressed.

[8] Color labels

Colors and names of ink tanks associated with the remaining ink levels appearing on the display.

[9] Keys

[Menu mode]

"

key" Displays the previous action or setting.

"

key" Displays the next action or setting.

"

key" Opens the menu one level above.

"

key" Opens the menu one level lower.

[Offline mode]

"

key" Feeds roll media manually in the direction opposite to the direction in which paper is ejected.

"

key" Feeds roll media manually.

[10] OK key

Sets or runs a selected action or value when the printer is in menu mode.

[11] eject key

Executing menu and ejects paper.

[12] Stop key

Quits a processing job.

[13] Power key

Switches the power to the printer on and off.

[14] Information key

Displays a printer submenu. Information about the inks and paper displays each time this key is pressed.
Hold this key for 3 seconds to clean the printhead.

OK

Online

Menu

Data

Message

Infomation

Power

Eject

Stop

Cleaning

(3 Sec.)

[4]

[5]

[3]

[2]

[7]

[8]

[1]

[9]

[10]

[14]

[11]

[13]

[12]

[6]

[a] [b]

«
...
27
28
29
30
31
...
»

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: MIMAKI Страницы: 2

Бренд: GCC Technologies Страницы: 130

Бренд: Highlight Страницы: 27

Бренд: iSys Страницы: 80

Бренд: Roland Страницы: 36

Бренд: Phoenix Contact Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды