Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя | Manualshive

Страница: 26 / 204

background image

Chapter 1

1-12

1.4.2 Interface specifications

0013-4625

a. [USB] (Standard)

(1) Interface Type
USB 2.0, full speed (12 Mbits/sec), high Speed (480 Mbits/sec)

(2) Methods of data transfer
Controlled transfer
Bulk transfer

(3) Signal level
Compliant with the USB standard.

(4) Interface cable
Twisted-pair shielded cable, 5.0 m or shorter
Compliant with the USB standard.
Wire AWG No.28, data line pair (AWG: American Wire Gauge)
AWG No.20 to No.28, distribution line pair

(5) Interface connector
Printer side: USB standard, Series B receptacle
Cable side: USB standard, Series B plug

b. [Network] (Standard)

(1) Interface Type
IEEE802.3-compliant interface

(2) Data transfer method
10Base-T/100Base-TX

(3) Signal level
Input: Threshold.
10Base-T: Max +585mV, min +300mV
100Base-TX: Turn-on +1000mV diff pk-pk, turn-off +200mV diff pk-pk
Output:
10Base-T: +2.2V - + 2.8V
100Base-TX: +0.95V - +1.05V

(4) Interface cable
Category 5 (UTP or FTP) cable, 100 m or shorter
Compliant with the ANSI/EIA/TIA-568A or ANSI/EIA/TIA-568B standard.

(5) Interface connector
Printer side: IEEE802.3 and ANSI X3.263-compliant, ISO/IEC60603-7 standard

c. [IEEE1394] (option)

(1) Interface Type
IEEE1394-1995, P1394a (Version 2.0)-compliant interface

(2) Method of data transfer
Asynchronous transfer

(3) Signal levels
Input:
Differential input voltage: +173mV - +260mV during S100 arbitration
+142mV - +260mV, receiving data
+171mV - +262mV during S200 arbitration
+132mV - +260mV, receiving data
+168mV - +265mV during S400 arbitration
+118mV - +260mV, receiving data
Output :
Differential output voltage: +172mV - +265mV

(4) Interface cable
Twisted-pair shielded cable, 4.5 mm or shorter.
Compliant with the IEEE1394-1995 or (Version 2.0) standard

(5) Interface connector
Printer side: IEEE1394-compliant, 6-pin connector (socket)
Cable side: IEEE1394-compliant, 6-pin connector (plug)
Cable side: Compliant with the ANSI/EIA/TIA-568A or ANSI/EIA/TIA-568B standard, Type RJ-45.

«
...
24
25
26
27
28
...
»

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Summa Страницы: 89

VersaUv LEF - 12i

Бренд: Roland Страницы: 100

SOLJET PRO4 XF-640

Бренд: Roland Страницы: 196

Бренд: Artistic Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды