manualshive.com logo in svg

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Поделиться
Скачать
Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя страница 147

Chapter 6

6-1

6.1 Troubleshooting

6.1.1 Outline

6.1.1.1 Outline of Troubleshooting

0013-1941

1. Overview

Targets of troubleshooting are classified into the troubles displayed on the LCD (i.e., warnings, errors, and service calls) and the troubles not displayed on the LCD.
Warnings and errors are displayed on the printer's LCD along with a code comprising alphanumeric characters.

2. Precautions for Troubleshooting

1) Check the environmental conditions and the media used.
2) Before starting troubleshooting, check that the connectors and cables are connected properly.
3) If you repair the printer with its external panel detached without disconnecting the AC cord from the outlet, take great care to prevent electric shock and short-
circuiting of PC boards.
4) Countermeasures to take after completion of troubleshooting are described starting with the most probable component that can cause the trouble determined by
troubleshooting. If there are two or more equally probable components, countermeasures are described starting with the component that requires the easiest repair.
After performing each countermeasure step, carry out test printing to check whether the problem has been solved. If not solved, try the next countermeasure step.
5) After completion of troubleshooting, check that all the necessary connectors and screws have been installed securely.
6) After completion of replacement or repair of a component, be sure to carry out test printing to make sure that the trouble has been solved.

6.2 Location of Connectors and Pin Arrangement

6.2.1 Main controller PCB

0019-6544

F-6-1

T-6-1

T-6-2

T-6-3

T-6-4

J1001 (USB)

Pin Number

Signal name

IN/OUT

Function

1

VBUS

IN

USB VBUS (+5V)

2

D-

IN/OUT

USB data (-)

3

D+

IN/OUT

USB data (+)

4

GND

-

USB GND

J1201 (to HDD)

Pin Number

Signal name

IN/OUT

Function

1

GND

-

GND

2

TXP

OUT

Transmission Data

3

TXN

OUT

Transmission Data

4

GND

-

GND

5

RXN

IN

Receive Data

6

RXP

IN

Receive Data

7

GND

-

GND

J1202 (to HDD)

Pin Number

Signal name

IN/OUT

Function

1

DASPN

IN

Access signal

2

+5V

IN

Power 5V)

3

GND

-

GND

J1801 (to power supply PCB)

Pin Number

Signal name

IN/OUT

Function

1

AFCONT

OUT

Normal/power saving switch signal

J1801

J2503

J3101
J3001
J3004
J2702

J2801

J1001

J2701

J2704

J2703

J2601

J3301

J2502

J3201

J3202

J2501

J3601

J3602

J3401

J1201

J1202

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды