manualshive.com logo in svg

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Поделиться
Скачать
Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя страница 113

Chapter 4

4-3

4.3 Points to Note on Disassembly and Reassembly

4.3.1 Note on locations prohibited from disassembly

0012-6356

Assemblies that are prohibited from disassembly and their adjustment outside the factory cannot be conducted are indicated by red screws.
Don't never loosen or remove the red screw, because normal operation and print can't be done if it is loosened or removed.

F-4-3

4.3.2 Moving the carriage manually

0012-6357

Move the carriage as required during disassembly/reassembly to prevent the carriage form contacting the parts to be removed.
The carriage does not move when capped. When uncapping moving the carriage, refer to the procedures in DISASSEMBLY/REASSEMBLY>Points to Note on
Disassembly and Reassembly>Opening the Cap/Moving the Wiper Unit.

4.3.3 Units requiring draining of ink

0012-6359

Before disassembling the units in the ink passage mentioned below, drain them of inks completely to prevent their leakage.
For instructions on how to drain units of inks, see Disassembly/Reassembly > Tips on Disassembly/Reassembly > Ink Drainage.

[1]Ink Tube Unit 

See Disassembly/Reassembly > Tips on Disassembly/Reassembly > Ink Tube Unit.

[2]Carriage Unit/Head Holder

See Disassembly/Reassembly > Tips on Disassembly/Reassembly > Carriage unit.

[3]Ink Tank Unit

See Disassembly/Reassembly > Tips on Disassembly/Reassembly > Ink Tank Unit.

F-4-4

[1]

[3]

[2]

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды