Canon IMAGERUNNER ADVANCE C5030, Руководство по обслуживанию, Страница: 453 / 1455

5
5
5-4
5-4
Adjustment > Image Formation System > Hopper Unit
Adjustment > Image Formation System > Hopper Unit
Image Formation System
Developing Assembly
Adjustment
procedure
Initialization of Developing Assembly (toner ratio and patch) is necessary and it
differs depending on the color.
If 4 colors are replaced simultaneously, execute INISET-4.
COPIER > FUNCTION > INSTALL > INISET-Y Initialization of Y Developing
Assembly (toner ratio and patch)
COPIER > FUNCTION > INSTALL > INISET-M Initialization of M Developing
Assembly (toner ratio and patch)
COPIER > FUNCTION > INSTALL > INISET-C Initialization of C Developing
Assembly (toner ratio and patch)
COPIER > FUNCTION > INSTALL > INISET-K Initialization of Bk Developing
Assembly (toner ratio and patch)
COPIER > FUNCTION > INSTALL > INISET-4 Initialization of 4-colors Developing
Assembly (toner ratio and patch)
Patch sensor
How to Replace
the Parts
Refer to “Removing the Patch Sensor (Front/Center/Rear)”.
Adjustment
procedure
Initialization of Patch sensor is necessary
COPIER > OPTION > IMG-MCON > P-ALPHA Input Patch Sensor alpha value
ITB Unit
How to Replace
the Parts
Refer to “Removing the ITB Unit”.
Adjustment
procedure
After replacement, execute the user mode (Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Adjust Gradation).
In case that the ITB Unit was removed, install the ITB Unit and execute the ITB
equilibrium position detection in service mode.
COPIER>FUNCTION>MISC-P>ITB-INIT <Level1>
This service mode will take approx. 2 to 3 minutes.
Remove the ITB Unit when replacing the following parts.
• ITB Cleaning Unit
• ITB
• Primary Transfer Roller
• Secondary Transfer Inner Roller
T-5-7
T-5-8
T-5-9
ITB
How to Replace
the Parts
Refer to “Removing the ITB”
Before
Installation
Check that the version of the machine is the following version or later.
MN-CON: Ver.34.05 D-CON: Ver.18.01
In case of prior version to the foregoing version, upgrade the machine and change
the value in the following service mode.
Select COPIER>OPTION>IMG-TR>ITB-TYPE, and change the setting from 0 to 1.
Adjustment
Procedure
Execute the user mode (Settings/Registration > Adjustment/Maintenance > Adjust
Image Quality > Auto Adjust Gradation).
Execute the ITB equilibrium position detection in service mode.
COPIER>FUNCTION>MISC-P>ITB-INIT <Level1>
This service mode will take approx. 2 to 3 minutes.
Secondary Transfer Outer Roller
How to Replace
the Parts
Refer to “Removing the Secondary Transfer Outer Roller/Secondary Transfer
Separation Guide Unit”.
Adjustment
Procedure
When replacing the Secondary Transfer Outer Roller, execute the following service
mode.
COPIER > FUNCTION > CLEANING > TNR-COAT
Hopper Unit
How to Replace
the Parts
Refer to “Removing the Hopper (M/Y/C/Bk)”.
Adjustment
Procedure
When installing the removed Toner Container, do not shake it.
When removing the Main Drive Unit simultaneously, install the Main Drive Unit and
Hopper Unit in that order.
Toner supply failure may occur.
In case that the Developing Assembly is replaced simultaneously, execute the
following service mode to initialize the Developing Assembly before installing the
Toner Container.
COPIER > FUNCTION > INSTALL > INISET-X (X: Color changed)
If the Toner Container is installed first, TD ratio of the Developing Assembly cannot
be set to a correct value.
T-5-10
T-5-11
T-5-12