Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 181

Copier Color | iR-ADV C3330/C3325/C3320 Series |

E302-0001 due to soiling on the mirror in the scanner unit

[Symptom]

E302-0001 may occur.
- E302-0001 : Shading error.( An error in the shading value was detected at white shading.)

[Cause]

Soiling on the mirror in the scanner unit.

[Service work]

When the above symptom occurs, follow the steps and clean the mirror in the scanner unit.
1) Remove the copyboard glass. Pull and move the timing belt [3] right and left to bring the scanner unit [1] to the center.
[Note] Try not to touch the 2 reader shafts [2] as much as possible as grease is applied on them.

2) To protect the scanner unit and keep it from getting soiled, fold a A4 size sheet [a] in half along short side and place it under
the scanner unit (top of the frame) as shown in the picture below.

3) Loosen the screw [1] and slide the sheet metal [2] in the direction of the arrow [a] to loosen the tensioner of the timing belt [3].
It is easier to perform the steps onwards by temporarily attaching the screw [1] while the tensioner is loosened.

4) Hold the scanner unit with left hand as shown in the photo below. While lifting it slightly, remove the timing belt with right hand.

176

«
...
179
180
181
182
183
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов