manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Руководство по устранению неисправностей, Страница: 145 / 200

Поделиться
Скачать
Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 145

Copier Color | iR-ADV C3330/C3325/C3320 Series |

ADF jam caused by flipped roller holder sheet or paper feed sheet
(DADF-AQ1)

[Symptom]

The original fed from ADF may get stuck to the roller holder sheet [1] or the paper feed sheet [2], resulting in a jam.

Jam Code

Sensor No.

0003, 0004, 0043, 0044, 0095

SR1

0009, 0010, 0049, 0050

SR2

0013, 0014, 0053, 0054

SR3

0095

SR5

[Cause]

Pulling the jammed paper towards to the upstream when clearing ADF jam, the paper may get stuck to the roller holder sheet [1]
or the paper feed sheet [2] causing these sheets to flip inward and remain in that state. When feeding paper from ADF in this
state, the paper gets stuck to the flipped sheets which are blocking the paper path. This causes the above symptom to occur.
The photo below [1] shows the roller holder sheet in a normal state and the photo [a] shows the sheet flipped inward [a]. The
photo below [2] shows the paper feed sheet in a normal state and the photo [b] shows the sheet flipped inward.

140

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов