Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 143

Jam (Delivery options)

Copier Color | iR-ADV C3330/C3325/C3320 Series |

Wrong stapling position or 1C14 jam after abnormal sound
(rasping sound) due to improper tray guide position of main body
(Inner Finisher-G1)

[Symptom]

During copying operation (set as 2 points stapling), abnormal sound (rasping sound) occurs and then wrong stapling position or
1C14 jam may occur.
- 1C14 jam : Retry Error (Assist Motor error)

[Cause]

Due to the improper installation position of tray guide [1] which is located at the time of inner finisher installation, the Inner Finisher-
G1 overlaps with the tray guide and then the frame (base plate) of Inner Finisher-G1 becomes deformed.
That results in the above mentioned symptom.
Fig.[A] shows the tray guide which is installed at proper position.

[Service work]

Install the tray guide of main body at proper position when Inner Finisher-G1 is installed.
Fig.[B] [C] [D] [F] show tray guides which are installed at improper positions.

138

«
...
141
142
143
144
145
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов