Canon imageRUNNER ADVANCE C2000 Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 175

Canon imageRUNNER ADVANCE C2000 Series Скачать руководство пользователя страница 101

pg. 99

[Caution] When you perform Auto Adjust Gradation, make sure to perform this for each paper type. The file
below shows recommended paper type for Japan, USA, and Europe.

Plain

Heavy

JPN CS-814 (81.4g)

GF-C209 (209g)

USA Hammermill Photo White (105g) Hammermill Color Copy Cover (162g)

EUR Canon High Grade (100g)

Canon High Grade (200g)

4. Change the paper interval value of ARCDAT control to "20" from "80" in Service Mode (Level 2) >
COPIER > Option > IMG-SPD > ARC-INT1. Setting range is between "10" to "500" (Default: 80).
[Caution]
- Actual setting value is calculated by dividing the entry value by 0.9 and rounding up after the decimal points.
(e.g.: If an entry value is 80, setting value will be 89. And if an entry value is 20, setting value will be 23.) First,
make sure to let the customer know that the productivity will slow down slightly after making the setting. After
the customer accepts this, make the setting.
- When a setting value of ARC-INT1 is changed to "20", be sure to perform the step 5).
5. Set ARC-INT2 to "20" or below in Service Mode (Level 2) > COPIER > Option > IMG-SPD.
[Caution] Do not set ARC-INT2 to a higher value than that of ARC-INT1.

Title

Output image becomes dark when the resolution is set at 1200dpi

Symptom

When the resolution is set at 1200dpi in the printer driver, output images become darker than those output at
600dpi.
This symptom is not affected by the data.
[A] is the output at 1200dpi, and [B] is at 600dpi.

«
...
99
100
101
102
103
...
»

Содержание imageRUNNER ADVANCE C2000 Series
















































































































































































Отзывы:

Нет отзывов