Canon imagePRESS Server M10 Скачать руководство пользователя

Страница: 32 / 98

Figure 13: Diagram of the motherboard

No.

Name

HDD data connector (SATA0)

Security chip (J23)

Battery (CR1)

Printer interface board (PCIEx16)

Power button pins (J11)

DIMM-A0

DIMM-B0

Crossover Ethernet port / Type A USB3.0 ports (x2)

Type A USB2.0 connector (x2)

Type A USB2.0 ports (x2) / Network port (RJ-45)

CPU and cooling assembly MS Mounting screws

24-pin power connector (J24)

4-pin power connector (PWRCONN1)

CPU fan connector (CPU FAN J16)

FRONT FAN connector (J30)

Service board connector (Port 80 Header) (EFI GPIO Header, J4)

Mounting screws

NOTE:

Any connectors not listed are not used.

■ Removing the motherboard

Before you remove the motherboard, you must remove:

3. REPLACING PARTS

Содержание imagePRESS Server M10


































































































Результаты поиска

Содержание imagePRESS Server M10

Отзывы:

Похожие инструкции для imagePRESS Server M10

Бренды по названию

Популярные бренды

Canon imagePRESS Server M10, Руководство по обслуживанию

Результаты поиска

Содержание imagePRESS Server M10

Отзывы:

Похожие инструкции для imagePRESS Server M10

Бренды по названию

Популярные бренды