Canon imagePRESS C800 Series Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 168

Canon imagePRESS C800 Series Скачать руководство пользователя страница 76

Install/Replace the Ethernet board

The extra Ethernet board (Intel PRO/1000 GT Desktop Adapter) is needed when IPDS functionality
is enabled (Extra license). The board is needed for the Codishell tool to analyse IPDS-problems. It
can also be used to connect the laptop to the PRISMAsync for imagePRESS C800 Series.

NOTE

When servicing components of the PRISMAsync for imagePRESS C800 Series always wear a

grounded strap around your wrist, to avoid electrostatic discharge that will harm your

equipment.

Step

Action

1

Remove side cover and middle bracket.

• Follow the instructions as described in

Access internal components on page 68

.

2

Unpack the new board.

3

Remove the fifth metal bracket (starting from the CPU).

• Use a Philips screwdriver to remove the bracket..

4

Place the board in the PCI connector.

• Firmly press the board in the PCI connector.

NOTE

Make sure to use the indicated slot.

5

Fasten the Ethernet board.

• Fasten the board with a single screw on the PCI bracket side with a Philips screw-

driver.

6

Re-install middle bracket and side cover.

• Make sure the fixing on the middle bracket is in position. It should fit exactly on the

Ethernet board.

7

Re-install system software

• If the Ethernet board is installed for the first time (no replacement) there will be no

driver installed for it. Therefore you have to re-install the PRISMAsync software.

Install/Replace the Ethernet board

76

Chapter 7 - Service procedures

«
...
74
75
76
77
78
...
»

Содержание imagePRESS C800 Series









































































































































































Отзывы:

Нет отзывов