Canon imagePRESS C800 Series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 168

Canon imagePRESS C800 Series Скачать руководство пользователя страница 75

Replace the Hard Disk Drives

The PRISMAsync for imagePRESS C800 Series is equipped with 3 x 250GB 3.5” SATA II HDD @
7200rpm Hard Disk Drives. One of the drives is used for the System software. The other 2 drives
are for data. Please check the table below for connections and purpose.

NOTE

When servicing components of the PRISMAsync for imagePRESS C800 Series always wear a

grounded strap around your wrist, to avoid electrostatic discharge that will harm your

equipment.

HDD # (position)

Connector

Purpose

0 (top)

SATA J18

System disk

1 (middle)

SATA J24

Data

2 (bottom)

SATA J16

Data

NOTE

• After replacement of the HDDs you will have to re-install the system software.
• Always exchange all 3 drives at once.
• The 2 data drives are Raid0 configured. This means that if 1 disk has crashed, all the data will

be lost.

Step

Action

1

Remove side cover.

• Follow the instructions as described in

Access internal components on page 68

2

Disconnect the connectors.

• Unplug the power and the SATA connectors on the HDD.

3

Remove the 2 screws on the front side.

4

Slide the HDD outward.

5

Insert the new HDD until it clicks into position.

6

Fasten the HDD with the 2 screws

7

Connect the connectors.

• Plug the power and the SATA connector on the HDD.

8

Repeat steps 2 thru 7 for the other 2 HDDs

9

Re-install middle bracket and side cover.

10

Re-install the system software.

• See

Re-installation of the system software on page 109

.

Replace the Hard Disk Drives

Chapter 7 - Service procedures

75

«
...
73
74
75
76
77
...
»

Содержание imagePRESS C800 Series









































































































































































Отзывы:

Нет отзывов