Canon imagePRESS 1135 Series Скачать руководство пользователя страница 33

Страница: 33 / 242

< Work procedure 1-3>

1 / 7

<Remedy>

_Check that the Engagement/Disengagement Cam of the Registration Slave Roller rotates

smoothly. (A loosened screw, a misaligned cam, etc.) [A],

_Check that the bearing at the Engagement/Disengagement Arm of the Registration Slave Roller

is rotating smoothly. [B],

_Check that the Drive Belt of the Registration Drive Roller rotates smoothly. [C],

_Check the connectors between the Registration Motor (M26) and the Registration/Duplexing

Driver PCB. [D]

<Detailed work procedure>

1) Open the Front Left Cover and the Front Right Cover.

2) Pull out the Fixing Feed Unit.

3) Open the duplex feed unit.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды