Canon imagePASS-A2 Скачать руководство пользователя страница 79

Страница: 79 / 82

PECIFICATIONS

The imagePASS has, or makes use of, the following features.

Hardware features

• 2.6GHz Intel Pentium dual core E5300 CPU

• Two 1GB DIMMs

• Hard disk drive

• 4 USB ports

• 10BaseT/100BaseTX/1000BaseTnetwork port for network printing

• 10BaseT/100BaseTX copier port for a crossover cable to the copier

(or to a PC for installing system software from DVD)

• 3V manganese dioxide lithium coin cell battery (Panasonic CR2032 or equivalent)

• Dedicated power supply

• Power switch

Physical specifications

• Operating Environment:

Temperature: +10

C to +35

Relative Humidity: 10%-90% (non-condensing)

• Power Supply Rating: 100 -240V, 50-60Hz, 2-4A

• Power Consumption: 72W (typical)

• Dimensions (Depth

Width

Height):

9.3 cm (3.7 in.)

33.6 cm (13.2 in.)

29.5 cm (11.6 in.)

• Weight: 5.4 kg (11.9 lb)

Networking and connectivity

The imagePASS has the following networking features:

• Supports AppleTalk and TCP/IP protocols simultaneously

• RJ-45 Ethernet LAN port for twisted pair (10BaseT/100BaseTX/1000BaseT) network

connection

OTE

The latest user software must be installed onto all computers that print to the

imagePASS. Using incompatible versions of the system and user software may result in system
problems. For more information, see the user documentation.

Содержание imagePASS-A2



















































































Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды

Canon imagePASS-A2, Руководство по обслуживанию

Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды