Canon imagePASS-A2 Скачать руководство пользователя страница 34

Страница: 34 / 82

ERVICE

ROCEDURES

CPU and CPU cooling assembly

The imagePASS includes an Intel Pentium dual core E5300 2.6GHz CPU. The CPU is
installed in a Zero Insertion Force (ZIF) socket on the motherboard.

Before removing the CPU from its socket, remove the motherboard from the chassis (see

page 28

), disconnect the CPU fan cable from the motherboard, and remove the cooling

assembly from the CPU socket (see

page 37

). The CPU cooling assembly consists of a fan and

a heatsink. The cooling assembly is secured to a mounting bracket on the underside of the
motherboard.

OTE

Do not remove the CPU fan from the heatsink.

IGURE

13:

CPU and CPU cooling assembly

CPU fan

Heatsink

Load plate

CPU socket on
motherboard

CPU

Socket lever

Mounting bracket

Содержание imagePASS-A2



















































































Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды

Canon imagePASS-A2, Руководство по обслуживанию

Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды