background image

119

Responding to Error Messages

In the case of [

q

], is Camera Connect running?

Establish a connection using Camera Connect (p.31).

In the case of [

l

], is the power of the printer on?

Turn on the printer.

Are the camera and the access point set to use the same 
encryption key for authentication?

This error occurs if the encryption keys do not match when the 
authentication method for encryption is set to [

Open system

].

The setting is case-sensitive, so check upper- and lower-case 
characters. Make sure that the correct encryption key for 
authentication is entered on the camera (p.85, 101).

Is the power of the target device and access point on?

Turn on the target device and access point, then wait a while. If a 
connection still cannot be established, perform the procedures to 
establish the connection again.

Is the camera too far from the target device or the antenna of 
the access point?

Bring the camera and the target device or the antenna of the 
access point closer together.

11:  Connection target not found

12:  Connection target not found

Содержание EOS 2000D

















































































































































Отзывы: