manualshive.com logo in svg

Canon EF-9, Руководство по обслуживанию

Поделиться
Скачать
Canon EF-9 Скачать руководство пользователя страница 19

II. PICK-UP/FEED SYSTEM

A. Pick-up/Feed System

Figure 2-2-1

The envelope feeder pick-up motor (SMT11) is a stepping motor that is rotated clockwise and
counterclockwise by the envelope feeder driver PCB.

When the motor rotates clockwise, all rollers in the envelope feeder are rotated.  When it

rotates counterclockwise, only the upper separation roller and feed rollers are rotated.

The envelope feeder driver PCB rotates the pick-up motor clockwise for about 1.0 second

when it receives the 1st Start command from the DC controller.  After 0.1 seconds, the motor is
rotated counterclockwise for about 1.9 seconds.  This process picks up and feeds the envelope
into the printer.

The envelope is stopped when it is 16mm past the registration paper sensor (PS1).  Following

this, the envelope feeder driver PCB rotates the pick-up motor counterclockwise for about 1 sec-
ond in response to the 2nd Start command sent from the DC controller to feed the envelope

2 - 3

CHAPTER 2

PS1

Transfer charging roller

Photosensitive drum

PS931

SMT11

Envelope feeder driver PCB

DC controller PCB

Serial line

SMT11: Envelope feeder pick-up motor
PS931: Envelope feeder paper sensor
PS1: Registration paper sensor (prinetr)

Envelope feeder
separation upper roller

Envelope
feeder pick-up
roller

Envelope feeder
feed roller

Envelope feeder

Torque
limiter

Envelope feeder
separation lower roller

Registration roller

➀

: ENVELOPE FEEDER PAPER SENSOR signal

➁

: ENVELOPE FEEDER PICK-UP MOTOR DRIVE signals

➀

➁

Содержание EF-9























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды