manualshive.com logo in svg

Canon DR-X10C - imageFORMULA - Document Scanner, Руководство пользователя

Поделиться
Скачать
Canon DR-X10C - imageFORMULA - Document Scanner Скачать руководство пользователя страница 45

45

Preparing the Document Eject Tray

The Eject Tray includes two Document Eject Guides, the Eject Tray 
Extension and Eject Paper Stopper, to be adjusted to match the length 
of your documents.

Document Guides

Slide the document eject guides to match the width of your 
documents.

Hint

• The position of the document eject guides can be shifted to the left 

or right by holding one guide in place while moving the other.

• To reset the guides so that they are equidistant from the center, 

spread the guides all the way to the left and right.

Document Eject Tray Extension

Pull out the tray extension to match the length of your document.

Eject Paper Stoppers

Raise the appropriate Eject Paper Stopper to stop ejected documents 
from spilling out of the eject tray.

Содержание DR-X10C - imageFORMULA - Document Scanner

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды