Canon DR-X10C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 13 / 160

background image

13

STEP 4

Connecting the Scanner to the Computer

There are two methods for connecting the DR-X10C scanner to a
computer: a USB connection to a standard USB port built in to the
computer, or SCSI connection to a SCSI card installed in an
expansion slot of the computer. Select the method that is best suited
to your computer environment.

Interface Connector Locations

The USB port and SCSI connector are located on the scanner as
shown below.

IMPORTANT

• Do not connect both USB and SCSI cables to the scanner at the

same time.

• Use only the supplied power cord.
• The scanner and computer should both be turned OFF when

making connections.

• Make sure that the computer is turned OFF before connecting the

SCSI cable. The scanner may not be properly recognized by the
computer if it is connected while the computer is turned ON.

• A SCSI cable is not supplied with the scanner. Obtain a cable with

connectors that match the SCSI connectors on both the scanner
and the computer.

Connecting the Scanner to the
Computer

To connect to the computer, follow the procedure for the intended
connection method.

Power Connector

A

USB Connector

B

SCSI Connector
(D-sub, 50-pin half-pitch)

C

DIP Switches for SCSI ID

«
...
11
12
13
14
15
...
»

Содержание DR-X10C - imageFORMULA - Document Scanner

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

IMAGE FORMULA DR-6010C

Бренд: Canon Страницы: 142

Бренд: ZKTeco Страницы: 46

Бренд: C-Pen Страницы: 20

Бренд: C-Pen Страницы: 8

Бренд: Janam Страницы: 2

Бренд: Navvis Страницы: 194

Бренд: Kodak Страницы: 50

Perfection 4490 Photo

Бренд: Epson Страницы: 21

Бренд: Epson Страницы: 56

Perfection 1670

Бренд: Epson Страницы: 8

PERFECTION 1250 Photo

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Perfection 4870 Pro

Бренд: Epson Страницы: 8

Perfection 1660 Photo

Бренд: Epson Страницы: 2

Perfection 3200 Pro

Бренд: Epson Страницы: 2

Perfection 3490 Photo

Бренд: Epson Страницы: 4

Perfection 4870 Photo

Бренд: Epson Страницы: 5

Perfection 4990 Photo

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды