Canon DR-X10C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 118 / 160

background image

118

✔

Is the scanner’s power switch turned ON?

If this does not solve the problem, consider the following possible
causes:

IMPORTANT

• It the scanner does not operate because of a system error, turn the

scanner OFF and wait at least 10 seconds before turning it back
ON. If errors continue to occur, reboot the scanner and computer.

• When scanning with configurations that use a large amount of the

computer’s memory, scanning will be performed properly for the
first scan. However, if a second scan is performed with the same
configurations, an error may occur due to insufficient memory and
scanning may not be possible. In such cases, restart the
application you are using and change the configurations before
scanning again.

Slow Scanning Speed

If the scanning speed is slow, first confirm the following:
Scanning may be slow if the USB interface does not support Hi-Speed
USB 2.0.

✔

Does the PC’s USB interface support only Full-Speed USB 1.1?

✔

Is the USB cable you are using the one that was supplied with the
scanner (Hi-Speed USB 2.0 compliant)?

✔

Is a USB 1.1-compliant device connected to the USB hub at the
same time?

If this does not solve the problem, consider the following possible
causes:

Documents Do Not Feed Properly

If a document does not feed properly, first confirm the following:

✔

Are pages sticking together because of static electricity or another
cause?

✔

Are you attempting to scan a document with size, paper thickness
or quality that is not supported by the scanner?

(See “Documents”

✔

Are the feed rollers dirty?

✔

Are the feed rollers worn out?

IMPORTANT

• Double feeding occurs when document pages stick together, and

incompatible paper thickness or quality can cause paper jams.
Check your documents carefully before loading.

Cause

The ISIS/TWAIN driver and Job Registration
Tool are not installed correctly

Solution

Uninstall and then reinstall the ISIS/TWAIN driver
and Job Registration Tool.

Cause

Other applications are running in the
background on your PC.

Solution

Quit all other applications that are running.

Cause

Resident applications, such as anti-virus
software, are draining memory resources.

Solution

Quit all resident applications.

Cause

Temporary files cannot be created in the
TEMP folder, as there is not enough free
space on the hard disk.

Solution

Delete unnecessary files on the hard disk to
increase free space.

«
...
116
117
118
119
120
...
»

Содержание DR-X10C - imageFORMULA - Document Scanner

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

Бренд: Visioneer Страницы: 122

Бренд: Leica Страницы: 144

Бренд: GRAPHTEC Страницы: 164

Бренд: Scoobe3D Страницы: 13

Workio KV-S7065C

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 48

Бренд: Datalogic Страницы: 2

Бренд: Scantron Страницы: 176

Бренд: Avision Страницы: 2

Бренд: Avision Страницы: 33

Бренд: TEKNIHALL Страницы: 46

OpticFilm 135 Series

Бренд: Plustek Страницы: 2

Бренд: Datalogic Страницы: 40

Бренд: Rowe Страницы: 144

Proventia ES1500

Бренд: IBM Страницы: 3

MANAGEMENT SITEPROTECTOR ES750

Бренд: IBM Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды