Canon DR-X10C - imageFORMULA - Document Scanner Скачать руководство пользователя

Страница: 103 / 160

103

• To avoid ink leakage, store spare ink cartridges inside their sealed

wrappers.

Replacing Ink Cartridges

Replace the ink cartridge using the following procedure.

IMPORTANT

After replacing an ink cartridge, run a test print to confirm proper
printing.

(See “Imprinter Testing” on p. 110.)

Replacing the Ink Cartridge (Pre-
Imprinter)

IMPORTANT

When the upper unit is raised, the pre-imprinter carriage moves to the
ink cartridge replacement position. Therefore, the scanner must be
ON when replacing the pre-imprinter ink cartridge.

Press the Open/Close button and carefully raise the
upper unit until it stops.

The carriage moves to the replacement position.

Ink Cartridge
Storage Pocket

Open/Close Button

Содержание DR-X10C - imageFORMULA - Document Scanner

































































































































































Результаты поиска

Содержание DR-X10C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды

Canon DR-X10C - imageFORMULA - Document Scanner, Руководство пользователя

Результаты поиска

Содержание DR-X10C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды