Canon DR 7090C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 5 / 129

background image

iv

Symbols Used in This Manual

The following symbols are used in this manual to explain
procedures, restrictions, handling precautions, and
instructions that should be observed for safety.

WARNING

Indicates a warning concerning operations that may lead to
death or injury to persons if not performed correctly. To
use the scanner safely, always pay attention to these
warnings.

CAUTION

Indicates a caution concerning operations that may lead to
injury to persons, or damage to property if not performed
correctly. To use the scanner safely, always pay attention
to these cautions.

IMPORTANT

Indicates operational requirements and restrictions. Be
sure to read these items carefully to operate the scanner
correctly, and avoid damage to the scanner.

Hint

Indicates a clarification of an operation, or contains
additional explanations for a procedure. Reading these
notes is highly recommended.

How This Manual is Organized

This manual consists of the following chapters.

■

Hardware

Chapter 1 Before You Start Using the Scanner

Provides an overview of the DR-7090C

Chapter 2 Setup

Describes the DR-7090C operating environment and how
to connect to a PC

Chapter 3 Basic Operation

Describes the basic uses of the DR-7090C

Chapter 4 User Modes

Describes the User Mode and other functions

Chapter 5 Maintenance

Describes routine cleaning and roller replacement

Chapter 6 Practical Examples

Describes displayed messages and troubleshooting
solutions

Chapter 7 Appendix

Provides a list of specifications and support information

■

Software

Chapter 8 ISIS/TWAIN Driver Settings

Describes the settings for the ISIS/TWAIN driver

Chapter 9 Job Registration Tool Settings

Describes the settings for the Job Registration Tool

Chapter 10 Practical Examples

Provides information for reference when making software
settings

«
...
3
4
5
6
7
...
»

Содержание DR 7090C - imageFORMULA - Document Scanner


































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR 7090C - imageFORMULA - Document Scanner

Бренд: Panasonic Страницы: 83

Бренд: Xante Страницы: 21

Бренд: Canon Страницы: 2

PIXMA TS5300 Series

Бренд: Canon Страницы: 16

Pixma TR7600 Series

Бренд: Canon Страницы: 12

PIXMA MX420 Series

Бренд: Canon Страницы: 34

PIXMA MX700 Series

Бренд: Canon Страницы: 7

Бренд: Canon Страницы: 44

PIXMA MG3220 series

Бренд: Canon Страницы: 5

Бренд: Canon Страницы: 92

PIXMA TS6200 Series

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 68

Бренд: Canon Страницы: 745

SmartBase MPC400

Бренд: Canon Страницы: 76

Бренд: Canon Страницы: 59

Бренд: Canon Страницы: 40

Бренд: Canon Страницы: 129

Бренд: Canon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды