Canon DR 7090C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 4 / 129

background image

iii

Introduction

Thank you for purchasing the Canon imageFORMULA DR-7090C Document Scanner. Please read this and the following manuals
thoroughly before using the scanner to become acquainted with its capabilities and make the most of its many functions.
After reading the manuals, store them in a safe place for future reference.

Manuals for the Scanner

The documentation for the scanner consists of the

Easy Start

Guide

and the

Reference Guide

(supplied with the scanner),

the

User Manual

(this manual), and the

CapturePerfect3.0

Operation Guide

, which are provided in electronic form and

registered in the menu during software installation.

Easy Start Guide

This manual describes the procedures for setting up the
scanner for use. Please follow the procedures in the

Easy

Start Guide

to set up the scanner.

Reference Guide

This manual consists of the basic scanner operating
instructions extracted from the

User Manual

.

User Manual (This Manual)

This manual consists of two sections: Hardware and
Software.
The Hardware section provides general information about
the scanner operational settings, maintenance, and
troubleshooting.
The Software section describes how to use the ISIS/
TWAIN driver with the scanner, and how to set up job
registration tools.

CapturePerfect 3.0 Operation Guide
(Electronic Manual)

This is the operation guide for CapturePerfect 3.0, the
Canon document scanner application program.

Hint

• The User Manual and the CapturePerfect 3.0 document files

are installed in the following locations during software
installation.

User Manual

CapturePerfect 3.0 Operation Guide

• Electronic versions of all manuals are available for viewing

from the Setup CD.

«
...
2
3
4
5
6
...
»

Содержание DR 7090C - imageFORMULA - Document Scanner


































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR 7090C - imageFORMULA - Document Scanner

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

ImageCLASS 2300

Бренд: Canon Страницы: 8

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

Color imageCLASS 8180c

Бренд: Canon Страницы: 95

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 49

ImageCLASS 2300

Бренд: Canon Страницы: 156

Бренд: Canon Страницы: 193

Бренд: QMS Страницы: 24

imageCLASS D1120

Бренд: Canon Страницы: 36

ImageCLASS 2300

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 66

Бренд: Ier Страницы: 8

Бренд: Magicard Страницы: 26

Бренд: QMS Страницы: 194

Бренд: quadient Страницы: 130

Бренд: Lexmark Страницы: 500

Бренд: Pantum Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды