Canon CR-X300 Скачать руководство пользователя страница 37

Страница: 37 / 114

Following aperture values can be set.

F1.8, F2.0, F2.2, F2.4, F2.6, F2.8, F3.1, F3.4, F3.7, F4.0, F4.4, F4.8, F5.2, F5.6, F6.2, F6.7, F7.3, F8.0, Closed*

* When the Iris is set to manual and the [Iris Limit] is off.

The aperture value that can be set differs depending on the zoom position. Reference aperture value is displayed on the

screen.

Maximum wide angle: F1.8 to F8.0, maximum telephoto: F2.8 to F8.0

Note

• To make the subject stand out by changing the depth of field and blur the background or surroundings, set a smaller aperture value ,

and to keep everything from close objects to far-away objects in focus, set a larger aperture value.

• When shooting in a bright location, narrowing down the iris can cause blurring. It is possible to prevent blurring by adjusting the ND filter

and shutter speed and opening the iris.

• When [AUTO] of the iris is set to off, the aperture value from Auto will be retained. The aperture value before setting to [AUTO] will not be

restored.

• In infrared shooting, iris is fixed open.

[ND Filter]

When the [Shooting Mode] is set to

(Iris Priority AE) or

(Manual Exposure) and the [Iris (Aperture Value)] is F4.0 or

larger, ND filter is automatically adjusted linked to the setting of the iris and its value will be displayed. In other shooting

modes, when [Iris (Aperture Value)] is F4.0 or larger, the exposure is automatically adjusted using the ND filter.

(Iris Priority AE),

(Manual Exposure),

(Program AE), or

(Shutter Priority AE), in order to adjust

the exposure without using the ND filter, [Auto] can be set to off.

Note

• When the [Shooting Mode] is set to

(Full Auto),

(Portrait),

(Sports),

(Low Light), or

(Spotlight), ND

filter is always automatically adjusted.

• The displayed value reflects the effect of the enhanced ND filter.

• In infrared shooting, ND filter cannot be set.

[

hutter Mode]

Adjusting the shutter speed enables to adapt to the subjects and the shooting environment, making it possible to capture

fast-moving subjects (sports, vehicles, etc.) clearly and brighten low-light scenes, etc. Shutter speed can be adjusted in the

following modes:

[Auto (sec.)]

Automatically adjusts the shutter speed according to the brightness of the video.

[

peed (sec.)]

Sets the shutter speed to seconds. The shutter speed can also be set to a value higher than the frame rate.

[

low (sec.)]

Sets the shutter speed slower than the frame rate to seconds. This setting is used for shooting in low-light areas.

Also, special effects such as "blurring the background" and "adding residual image effects to zoom" are available for

shooting a moving subject with pan operation.

For precautions when shooting in slow, refer to "About Shooting with Slow Shutter" (P. 39).

[Clear

can (Hz)]

Sets the shutter speed by frequency. This is used to reduce black bands on the screen and flickering from fluorescent

lighting, or to fine tune the brightness.

The shutter speed that can be selected differs depending on the frame frequency.

hutter Mode

Frame Frequency (Hz)

23.98

29.97

59.94

25.00

50.00

Auto (sec.)

1/24 - 1/2000

1/30 - 1/2000

1/60 - 1/2000

1/25 - 1/2000

1/50 - 1/2000

Speed (sec.)

1/24 - 1/2000

1/30 - 1/2000

1/60 - 1/2000

1/25 - 1/2000

1/50 - 1/2000

Slow (sec.)

1/6, 1/12

1/8, 1/15

1/8, 1/15, 1/30

1/6, 1/12

1/6, 1/12, 1/25

Clear Scan (Hz)

23.98 - 250.38

29.97 - 250.38

59.94 - 250.38

25.00 - 250.40

50.00 - 250.40

Содержание CR-X300



















































































































Результаты поиска

Содержание CR-X300

Отзывы:

Похожие инструкции для CR-X300

Бренды по названию

Популярные бренды

Canon CR-X300, Руководство пользователя

Результаты поиска

Содержание CR-X300

Отзывы:

Похожие инструкции для CR-X300

Бренды по названию

Популярные бренды