Canon CP660 Скачать руководство пользователя страница 267 | Manualshive

Страница: 267 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 8 INSTALLATION

8-17

No.

1

2

3

4

Work

Turn off of the printer unit.

Unpack the duplexing unit.

Remove the tape, stopper, and spacers from
the duplexing unit.

Open the printer assembly delivery cover.

Remarks

Remove the tape.

Remove the stopper.

Remove the spacers.

IV. INSTALLING THE DUPLEXING UNIT

The areas near the fixing assembly
and the delivery assembly behind the
printer unit delivery cover are hot, pos-
sibly burning the skin upon contact.
If the printer unit has been used, turn it
off, and wait for a while for its inside to
cool before starting the work.

Caution

:

Download free service manual at http://printer1.blogspot.com

«
...
265
266
267
268
269
...
»

Содержание CP660
























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CP660

Бренд: D-Link Страницы: 12

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

Replicator Mini+

Бренд: MakerBot Страницы: 2

Replicator Mini Compact

Бренд: MakerBot Страницы: 38

Бренд: MakerBot Страницы: 14

Бренд: SainSmart Страницы: 13

Бренд: Xerox Страницы: 12

Бренд: Duplo Страницы: 123

Бренд: Ricoh Страницы: 278

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды