Canon Colorado M Series Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 378

Canon Colorado M Series Скачать руководство пользователя страница 76

Change the media settings

Introduction

You can change the media settings of a media profile in the RIP.

When to do

Only when you create a new media profile or edit an existing media profile you can tune the
media settings. It is advised to use the Colorado M-series media profiles and not change the
media settings. Only advanced users or application specialists should edit media profiles and
have to tune the media settings.

IMPORTANT

Changing the media settings can cause damage to your printer which may void your machine
warranty service.

NOTE

• Changing the media settings can result in poor print quality.
• This manual provides you with basic information in order to create and change media

profiles. Profiling is an expert task which requires additional information and tools not
covered by this manual. Contact your local support organization when you want to create or
change media profiles.

Before you begin

The location of the media settings differs, depending on the RIP you are using. For more
information, see

Manage media profiles in ONYX on page 44

Manage media profiles in Caldera

Change the media settings

76

Chapter 4 - Handle the media

«
...
74
75
76
77
78
...
»

Содержание Colorado M Series



























































































































































































































































































































































































Отзывы:

Нет отзывов